Huawei NetCol5000-C030H90D0 Скачать руководство пользователя страница 158

Страница: 158 / 206

Step 2 Open the front door, remove cables from the faulty fan, use a Phillips screwdriver

to remove the four screws from the faulty fan, and remove the faulty fan.

Figure 6-3 Removing a fan (NetCol5000-C065)

Figure 6-4 Removing a fan (NetCol5000-C030/C032)

Step 3 Install the new fan in a reverse order of the removal.

Step 4 Connect cables to the new fan and close the front door.

Step 5 Choose Maint > Fan Maintenance on the home screen to locate the SN of the

faulty fan, and tap Power On.

Step 6 Tap Maint > Performance Maint on the home screen and clear the fan runtime.

----End

6.4.4 Replacing the Wet Film Humidifier

NetCol5000-C(030, 032, 065) In-row Chilled Water

Smart Cooling Product

User Manual (2019)

6 System Operation and Maintenance

Issue 03 (2020-08-30)

150

Содержание NetCol5000-C030H90D0















































































































































































































Результаты поиска

Содержание NetCol5000-C030H90D0

Отзывы:

Huawei NetCol5000-C030H90D0, Руководство пользователя, Страница: 158 / 206

Результаты поиска

Содержание NetCol5000-C030H90D0

Отзывы: