Huawei NetCol5000-C030H90D0 Скачать руководство пользователя

Страница: 100 / 206

Step 2 Set teamwork control parameters.

All teamwork control parameters can be set on the master smart cooling product.

Only Teamwork group No., Smart cooling product address, Enable teamwork

CAN resistor, Teamwork function and Networking mode can be set on slave

smart cooling products. Other parameters of the slave units will be modified by

the master unit synchronously.

Table 4-6

describes how to set the parameters.

Table 4-6 Teamwork settings

Parameter

Description

Configuration

Principle

Default

Value

Teamwork

group No.

The number of the

teamwork controlled

group, which is the

same for all the

devices in the group.

Set the assigned

teamwork control

number.

Air

conditioner

address

Smart cooling

product addresses

should be different

from each other.

Set the assigned unit

address.

Enable

teamwork

CAN resistor

Indicates the build-

out resistor status of

each smart cooling

product in a

teamwork group. Set

the parameter if CAN

network is used.

● Set this parameter to

No for non-

teamwork scenarios.

● For teamwork

scenarios, set this

parameter to Yes for

the first and last

smart cooling

products in a

teamwork group,

and set it to No for

other smart cooling

products.

Teamwork

function

Disable or enable the

teamwork function. If

the teamwork

function is disabled,

this device is

operating according

to its own control. If

the teamwork

function is enabled,

this device works in

harmony with others

that in the same

group.

Set this parameter

based on the onsite

device heat distribution.

Disable

NetCol5000-C(030, 032, 065) In-row Chilled Water

Smart Cooling Product

User Manual (2019)

4 Commissioning

Issue 03 (2020-08-30)

Содержание NetCol5000-C030H90D0















































































































































































































Результаты поиска

Содержание NetCol5000-C030H90D0

Отзывы:

Похожие инструкции для NetCol5000-C030H90D0

Бренды по названию

Популярные бренды

Huawei NetCol5000-C030H90D0, Руководство пользователя

Результаты поиска

Содержание NetCol5000-C030H90D0

Отзывы:

Похожие инструкции для NetCol5000-C030H90D0

Бренды по названию

Популярные бренды