Huawei FusionModule1000B V100R003C00 страница 84 Скачать руководство пользователя | Manualshive

Страница: 84 / 111

background image

FusionModule1000B Water-Cooled IT Solution
Commissioning Guide

9 Commissioning Core Components

Issue 02 (2017-01-10)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

78

9.1.3 (Optional) Commissioning the UPS2000-G

Prerequisites



The upstream PDC of the UPS2000-G has been powered on.



Battery packs or batteries have been installed and connected, and the installation has
been verified.

Preparations

Tool: Phillips screwdriver

Documents: documents delivered with the UPS2000-G, power supply and distribution system
diagram, power supply and distribution component layout, UPS2000-G single system initial
configuration table, UPS2000-G parallel system initial configuration table

Skill requirement: power distribution system engineer

For the diagrams and tables, see the initial configuration parameter manual for the solution in use.

Procedure

Step 1

Switch on the input power circuit breaker of the UPS2000-G to power on the UPS2000-G.

If the output circuit breaker cannot be switched on within 5 minutes after the UPS2000-G
input power circuit breaker has been switched on, disconnect the input power circuit breaker.
Otherwise, the UPS2000-G will enter the protection mode automatically.

Step 2

Start the UPS2000-G and verify the initial configurations.



If an alarm is generated after the power-on, rectify the fault before continuing the
power-on commissioning.



During the power-on commissioning, you are not allowed to switch on the bypass circuit
breaker for the UPS2000-G.



During the UPS2000-G power-on commissioning, you are not allowed to modify the
UPS2000-G initial configurations unless you are authorized by onsite Huawei engineers.

Step 3

Enter the user name and password to enter the operation screen, and verify that initial
parameter settings are consistent with the initial configuration table.

«
...
82
83
84
85
86
...
»

Содержание FusionModule1000B V100R003C00
















































































































Отзывы:

Нет отзывов

Похожие инструкции для FusionModule1000B V100R003C00

WD Caviar Green WD10EADS

Бренд: Western Digital Страницы: 2

Бренд: FAST LTA Страницы: 8

SOHORAID ST4-TB3

Бренд: Stardom Страницы: 25

Бренд: Ravpower Страницы: 15

Бренд: Arrow Storage Products Страницы: 44

Бренд: Convex Страницы: 19

OmniStor 4900F Series

Бренд: Rackable Systems Страницы: 196

Бренд: IBM Страницы: 2

Бренд: ABB Страницы: 2

Бренд: HOLZMANN MASCHINEN Страницы: 51

Askham Tool Store

Бренд: Garden Furniture Direct Страницы: 5

PERSONAL MEDIA DRIVE

Бренд: HP Страницы: 16

Pavilion p6210f

Бренд: HP Страницы: 1

Бренд: HP Страницы: 15

Бренд: HP Страницы: 33

StorageWorks 1/8

Бренд: HP Страницы: 6

Бренд: HP Страницы: 34

Бренд: HP Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды