Huawei FusionModule1000B V100R003C00 страница 90 Скачать руководство пользователя | Manualshive

Страница: 90 / 111

background image

FusionModule1000B Water-Cooled IT Solution
Commissioning Guide

9 Commissioning Core Components

Issue 02 (2017-01-10)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

84

Figure 9-4

DIP switch on the main control board of a precision air conditioner

(1) Teamwork ports 1 and 2

(2) DIP switches on the main control board

(3) J127 FE port (reserved)

The S1 switch toggle exists on the Arm7 main control board, but does not exist on the M4 main control
board. For the Arm7 main control board, you need to set the switch toggle. For the M4 main control
board, you just need to verify the settings against the cooling device initial configuration table.

Procedure

Step 1

Check the DIP switch settings for each 30 kW chilled water precision air conditioner by
referring to the initial DIP switch configuration table for the main control board of the 30 kW
chilled water precision air conditioner.

Step 2

(Optional) If any DIP switch setting is inconsistent with the initial setting, change it to the
initial setting.

Disconnect the power supply before setting the DIP switch.

----End

9.2.2.3 Teamwork Initial Configuration

Prerequisites

You have powered on the 30 kW chilled water precision air conditioners.

«
...
88
89
90
91
92
...
»

Содержание FusionModule1000B V100R003C00
















































































































Отзывы:

Нет отзывов

Похожие инструкции для FusionModule1000B V100R003C00

ShareCenter DNS-343

Бренд: D-Link Страницы: 12

Бренд: Tab Страницы: 26

2big Thunderbolt

Бренд: LaCie Страницы: 72

Бренд: Far Tools Страницы: 10

Бренд: ZRGP Страницы: 33

Бренд: Edsal Страницы: 2

Бренд: EditShare Страницы: 112

xl-raid-2804issa

Бренд: XtendLan Страницы: 124

Бренд: XtendLan Страницы: 14

Бренд: Habey Страницы: 4

Бренд: OneTouch Страницы: 10

Бренд: Grizzly Страницы: 8

Бренд: Grizzly Страницы: 6

Бренд: Grizzly Страницы: 8

Бренд: Grizzly Страницы: 32

Бренд: Sonnet Страницы: 8

Бренд: Absco Страницы: 18

Бренд: ramia Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды