Huawei FusionModule1000B V100R003C00 Скачать руководство пользователя

Страница: 47 / 111

FusionModule1000B Water-Cooled IT Solution
Commissioning Guide

6 Power-On Commissioning

Issue 02 (2017-01-10)

Huawei Proprietary and Confidential

System

Check Item Content

Check Standard

Civil air
conditioner
(optional)

See
document
s
delivered
with the
civil air
conditione
r.

Management
system

Power-on
commissioni
ng for the
monitoring
components

Hydrogen
collector

The hydrogen density displayed on the
hydrogen collector is 0% or 1%.

Hydrogen
sensor

Camera

The red indicator inside the camera is on.

VCN500



The green power indicator of the VCN500
is steady on.



If the ACT indicator blinks green, data
transmission is normal.



If the Active indicator of the hard disk
blinks green, data can be read from the
hard disk properly.

RH2288
server

The power indicator of the RH2288 server is
normal.

LAN
switch

The PWR1, PWR2, and SYS indicators are
on.

ECC500



The Power indicator on the main control
board is on.



The PWR and RUN indicators on the
MUE and MUS modules are on.

Independe
ntly
deployed
modules

The PWR and RUN indicators are on.

Water
sensor

The power indicator is on.

Polymer
temperatu
re and
humidity
(T/H)
sensor

Displays the temperature and humidity values.

Intelligent
battery
monitorin
g module

The RUN and LINK indicators are on.

Содержание FusionModule1000B V100R003C00
















































































































Результаты поиска

Содержание FusionModule1000B V100R003C00

Отзывы:

Похожие инструкции для FusionModule1000B V100R003C00

Бренды по названию

Популярные бренды

Huawei FusionModule1000B V100R003C00, Руководство по вводу в эксплуатацию

Результаты поиска

Содержание FusionModule1000B V100R003C00

Отзывы:

Похожие инструкции для FusionModule1000B V100R003C00

Бренды по названию

Популярные бренды