HP X Class 500/550MHz Скачать руководство пользователя страница 111

Страница: 111 / 149

Chapter 5

111

Tests and Error Messages

MaxiLife Test Sequence and Error Messages

The first detected error displays a message on the LCD status panel. If this happens, one
of the following screens could appear.

The following diagram shows how the Pre-boot Diagnostics works when it encounters an
error.

Figure 5-1. How Pre-boot Diagnostics Works When It Encounters An Error

Error!

Power supply

Error!

CPU Socket

Error!

Power CPU 1

Error!

Board PLL

Missing or
incorrectly
installed CPU
or Termina-

Presence of CPUs or

Terminators in the Processor

Control of Some Voltages: VRMs, 12V

Error!

Power CPU 2

VRM or CPU power supply are not connected.
If an Error! Power is displayed, the likely cause
could be that the power supply is not connected,
or the VRM is installed with an unpopulated
CPU socket (unsupported configuration).

CPU Board is not connected,
or the system board needs
replacing.

Control of the CPU Board

Error!

RAM type

No Dimms are
detected.

Number and Compatibil-

ity of DIMMs

Installed DIMMs
are not compatible.
This is in fact the
BIOS that is
checking the

Error!

No RAM

Video board is not
installed.
This test is executed by

Video Board

Error!

No Video

Error!

CPU Socket

MaxiLife Firm-

LCD Status

Panel

C Bus

DIMM

Voltage CPU1,

Voltage 12V

CPU or Termina-

PLL Frequency

Vcc State (5V)

PGOOD (VRM output)

An error has been detected when
checking the CPU and Terminator.
The displayed error message could
indicate a missing CPU or

DIMM

Содержание X Class 500/550MHz






















































































































































Результаты поиска

Содержание X Class 500/550MHz

Отзывы:

Похожие инструкции для X Class 500/550MHz

Бренды по названию

Популярные бренды

HP X Class 500/550MHz, Справочное руководство

Результаты поиска

Содержание X Class 500/550MHz

Отзывы:

Похожие инструкции для X Class 500/550MHz

Бренды по названию

Популярные бренды