HP X Class 500/550MHz Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 149

background image

48

Chapter 2

System Board

Hot Bus

Optional Second Microprocessor

HP V

ISUALIZE

Personal Workstations have dual processing capability. Installing a second

processor is only advantageous when the software can make use of parallel activity. In
particular, you need to be running a multi-threaded operating system that supports
multiprocessing (one that is MPS-ready), such as Windows NT. The Windows NT operating
system makes the best use of the Pentium III’s 32-bit architecture (though other operating
systems will also show some benefit if 32-bit application programs are run).

The following table summarizes the supported operating systems:

The two processors must be operating at the same processor speed, and both, or neither,
must support the processor internal ECC functionality.

Configuring Setup for Multi-Processing

HP V

ISUALIZE

Personal Workstations support Symmetric Multi-Processing (SMP). When

adding a second processor, you must ensure that: (a) the “multi-processing” choice has
been made in the system Setup; (b) the operating system supports multi-processors.

In the case of Windows NT, it might be necessary to perform an upgrade from the MPS
uniprocessor to the MPS multi-processor version.

NOTE

The system Setup allows a choice between “mono or multi-processing”
operations. The “mono-processing” mode has been implemented in order to
support operating systems that rely on the “legacy” interrupt controller
82C59 and are not aware of I/O APIC controller 820093AA operation. Refer to
the section “Interrupt Controllers” in the chapter “HP BIOS” for further
details.

Table 2-6. Summary of Supported Operating Systems

Windows NT 4.0 (or greater)

Windows 95 and Windows 98

Multi-threaded

Yes

Yes

MPS-ready

Yes

No

32-bit operating system

Yes

Partial

1

1. 32-bit operation at the outermost levels, but only 16-bit working internally.

32-bit applications available

Yes

Yes

«
...
46
47
48
49
50
...
»

Содержание X Class 500/550MHz






















































































































































Отзывы:

Нет отзывов

Похожие инструкции для X Class 500/550MHz

Бренд: Accessory Power Страницы: 4

Бренд: Renesas Страницы: 18

Бренд: ConvaTec Страницы: 4

Бренд: Black Box Страницы: 16

XAV1501 - Powerline AV+ 200 Adapter

Бренд: NETGEAR Страницы: 2

Бренд: TRENDnet Страницы: 9

Sabrent USB-DSC8

Бренд: Hitachi Страницы: 21

Бренд: Hitachi Страницы: 4

Бренд: Hitachi Страницы: 28

Бренд: Hitachi Страницы: 76

Бренд: Hitachi Страницы: 184

Бренд: Hitachi Страницы: 190

Бренд: JVC Страницы: 44

Бренд: Canon Страницы: 52

Бренд: Canon Страницы: 51

Бренд: Canon Страницы: 2

Бренд: Canon Страницы: 1

Бренд: Canon Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды