HP X Class 500/550MHz Скачать руководство пользователя страница 113 | Manualshive

Страница: 113 / 149

background image

Chapter 5

113

Tests and Error Messages

MaxiLife Test Sequence and Error Messages

Post Test Sequence and Post Error Codes

In order to check that the CPU is able to run the BIOS boot code (POST phase) from the
first CPU instructions through to DIMM detection, MaxiLife firmware waits for a
synchronization event from the BIOS. Any failure that prevents the execution of the
firmware will therefore trigger the BIOS error and will display the following message on
the LCD status panel.

Then, the BIOS executes the Power-On Self Test (POST) sequence. In this phase, MaxiLife
waits for any error messages that the BIOS may issue. If such an error occurs, then a
screen similar to the following example is displayed. The error code that appears on the
LCD status panel is the same as the one that appears on the Personal Workstation screen.
If the POST issues several error codes, only the last one is visible on the LCD status panel.

Compatibility of DIMMs. The
BIOS checks that the inserted
DIMMs are both compatible with
one another, and compatible with
the Front Side Bus frequency.

RAM TYPE

Check the installed memory modules. This
error occurs when mixing incompatible
memory modules, or when mixing
Unbuffered and Registered memory modules.

Availability of video controller. It
is checked by the BIOS. If an
error is detected, it is not a fatal
one and the BIOS will continue
its execution normally.

NO VIDEO

Check that the video controller is correctly
installed.

Note: No error is detected if a monitor is not
connected to an installed video controller.
This is not a fatal error and the BIOS will
continue its normal execution.

Table 5-1. Basic Pre-boot Diagnostics

Test

Error Code

Action to Take

Error!

BIOS

Error!

POST XXXX

Where XXXX =
POST error code

«
...
111
112
113
114
115
...
»

Содержание X Class 500/550MHz






















































































































































Отзывы:

Нет отзывов

Похожие инструкции для X Class 500/550MHz

Бренд: Parker Страницы: 36

FreeAgent DockStar

Бренд: Seagate Страницы: 13

Бренд: National Instruments Страницы: 2

WiFi 2.4G RJ45 A

Бренд: Epever Страницы: 2

Бренд: Cellink Страницы: 31

Бренд: Tailwind Страницы: 3

2208USB/ETH - annexe 1

Бренд: SMC Networks Страницы: 24

Бренд: Roving Networks Страницы: 8

2940U - AHA Storage Controller Ultra SCSI 20 MBps

Бренд: Adaptec Страницы: 14

Бренд: Abocom Страницы: 62

Бренд: Clarity Страницы: 8

Бренд: Choetech Страницы: 38

Бренд: Optoma Страницы: 26

HN-Power HNP11-MicroUSBV2

Бренд: HN Electronic Components Страницы: 4

BLACKJACK-APTT1

Бренд: Camplex Страницы: 6

Single Slot Dock Ethernet Module

Бренд: Datalogic Страницы: 2

Бренд: Abocom Страницы: 1

Бренд: Connect Tech Страницы: 79

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды