HP X Class 500/550MHz Скачать руководство пользователя страница 42

Страница: 42 / 149

Chapter 2

System Board

Chipset

PIIX4E (82371EB)

Table 2-3. PIIX4E (82371EB) Chip Features

Feature

Multifunction PCI to ISA Bridge, supports

• PCI at 30 MHz and 33 MHz.

• PCI Rev 2.1 Specification.

• Full ISA or Extended I/O (EIO) Bus.

• Full Positive Decode or Subtractive Decode

of PCI.

• ISA and EIO at of PCI Frequency.

Enhanced DMA Controller

• Two 82C37 DMA controllers.

• Supports

PCI

DMA

with

PC/PCI

Channels and Distributed DMA Protocols
(simultaneously).

• Fast Type-F DMA for reduced PCI Bus

usage.

Supports both Mobile and Desktop Deep
Green Environments

• 3.3V Operation with 5V Tolerant Buffers.

• Ultra-low Power for Mobile Environments

Support.

• Power-On

Suspend,

Suspend

RAM,

Suspend to Disk, and Soft-Off System
States.

• All Registers Readable and Restorable for

Proper Resume from 0.V Suspend.

Interrupt Controller Based on TWo 82C59

• 15 Interrupt support.

• Independently

programmable

for

Edge/Level sensitivity.

• Supports Optional I/O APIC.

• Serial Interrupt Input.

Power Management Logic

• Global and Local Device Management.

• Suspend and Resume Logic.

• Supports Thermal Alarm.

• Support for external microcontroller.

• Full support for Advanced Configuration

and Power Interface (ACPI) Revision 1.0
specification,

and

Directed

Power

Management.

Integrated IDE Controller

• Independent Timing of up to four drives.

• PIO Mode 4 and Bus Master IDE transfers

up to 14 Mbytes/sec.

• Supports “Ultra DMA/33” Synchronous

DMA Mode transfers up to 33 Mbytes/sec.

• Integrated 16 x 32-bit buffer for IDE PCI

Burst transfers.

• Supports Glue-less “Swap-Bay”.

• Option with Full Electrical Isolation.

USB

• Two USB 1.0 Ports for Serial transfers at

12 or 1.5 Mbit/sec.

• Supports UHCI Design Guide.

Real Time Clock

• 256-byte battery-backed up CMOS SRAM.

• Includes Date Alarm.

• Two 8-byte Lockout Ranges.

Содержание X Class 500/550MHz






















































































































































Результаты поиска

Содержание X Class 500/550MHz

Отзывы:

Похожие инструкции для X Class 500/550MHz

Бренды по названию

Популярные бренды

HP X Class 500/550MHz, Справочное руководство

Результаты поиска

Содержание X Class 500/550MHz

Отзывы:

Похожие инструкции для X Class 500/550MHz

Бренды по названию

Популярные бренды