HP X Class 500/550MHz Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 149

background image

24

Chapter 1

System Overview

Specifications and Characteristics Data

Operating temperature and humidity ranges may vary depending upon the mass storage devices
installed. High humidity levels can cause improper operation of disk drives. Low humidity levels
can aggravate static electricity problems and cause excessive wear of the disk surface.

Table 1-5. Power Consumption

Power Mode

Power Consumption

Operating

85 W (average)

Idle

75 W (average)

Off

6.5 W (average)

Table 1-6. Environmental Specifications

Environmental Specifications (System Processing Unit, with Hard Disk)

Operating Temperature

+5˚C to +40˚ (+40˚F to +104˚F)

Storage Temperature

−

40˚C to +70˚C (

−

40˚F to +158˚F)

Over Temperature Shutdown

+50˚C (+122˚F)

Operating Humidity

15% to 80% (relative)

1

Storage Humidity

8% to 80% (relative)

1

Acoustic noise emission:
Sound power – with 10.0krpm SCSI hard disk drive

(as defined by ISO 7779)
LwA < 50 db

Operating Altitude

10000 ft (3100m) max

Storage Altitude

15000 ft (4600m) max

1. Non-condensing conditions

«
...
22
23
24
25
26
...
»

Содержание X Class 500/550MHz






















































































































































Отзывы:

Нет отзывов

Похожие инструкции для X Class 500/550MHz

Бренд: Hanwha Techwin Страницы: 2

Бренд: Weego Страницы: 6

Бренд: ZyXEL Communications Страницы: 8

Бренд: BASETech Страницы: 6

Бренд: Jameco Electronics Страницы: 31

Бренд: dji Страницы: 40

Бренд: Conceptronic Страницы: 2

Бренд: TOOLCRAFT Страницы: 2

Бренд: Prudent Way Страницы: 6

Бренд: Johnson Controls Страницы: 5

IEEE 802.11b WLAN USB Adapter

Бренд: Kobian Страницы: 25

Бренд: Asante Страницы: 60

Бренд: Sony Страницы: 56

Бренд: Sony Страницы: 64

Бренд: Sony Страницы: 90

Бренд: Sony Страницы: 100

Бренд: Sony Страницы: 124

Бренд: Sony Страницы: 125

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды