HP X Class 500/550MHz Скачать руководство пользователя страница 128

Страница: 128 / 149

128

Chapter 5

Tests and Error Messages

Error Message Summary

The Error Message Utility or EMU (.COM application written in C language) is to provide
full screen online help messages (localized) on most common POST errors. When an error
is generated in POST during the boot process, EMU is run by typing

ENTER

. The entry

point of each EMU message is a 4-digits error code generated by POST.

If the POST reports an error, one of the following four error categories will be displayed.

Category #1:

if the error requires Setup to be run, the POST should prompt:

<F1= Continue>, <F2= Setup>, <Enter= View System Error>

and pause. (Refer to autoconfig specification for more details on POST prompts)

Category #2:

if the error is only a warning (i.e. key stuck), the POST should prompt:

<Enter= View System Error>

for 2 seconds then boot. (Refer to autoconfig specification for more details on POST
prompts)

Category #3:

if the error occurs because a device has been unplugged or removed, the
POST should prompt :

“If errors are reported because one or more of the listed components have been removed,
press <F4> to validate the changes.”

<F1= Continue>, <F2= Setup>, <F4= Validate Change>, <Enter= View System Error>

and pause. (Refer to autoconfig specification for more details on POST prompts)

Category #4:

if the error is serious, the POST should prompt:

The BIOS has detected a serious problem that prevents your Personal Workstation
from booting.”

<F2= Setup>, <Enter= View System Error>

and stop. Only the setup and the EMU can be run. The BIOS must never boot on

HDD.

Содержание X Class 500/550MHz






















































































































































Результаты поиска

Содержание X Class 500/550MHz

Отзывы:

Похожие инструкции для X Class 500/550MHz

Бренды по названию

Популярные бренды

HP X Class 500/550MHz, Справочное руководство

Результаты поиска

Содержание X Class 500/550MHz

Отзывы:

Похожие инструкции для X Class 500/550MHz

Бренды по названию

Популярные бренды