HP X Class 500/550MHz Скачать руководство пользователя страница 112

Страница: 112 / 149

112

Chapter 5

Tests and Error Messages

MaxiLife Test Sequence and Error Messages

The following table shows the test sequence carried out, the type of error message, and the
action to take.

Table 5-1. Basic Pre-boot Diagnostics

Test

Error Code

Action to Take

Presence of a processor in the
BOOT PROC [1] processor slot.
This is test is for a single
processor system only.

NO CPU 1

Check that the processor is correctly installed
in the BOOT PROC [1] slot.

Presence of either CPU or
Terminator in the processor slot.

CPU
SOCKET

Check CPUs and Terminator and VRM of
installed processor.

Number of installed DIMMs

NO RAM

Check that the memory module is correctly
installed in the memory socket.

Control of some voltages: VRMs,
12V

POWER
SUPPLY

Check the power supply connectors, VRM,
CPU. In a single
processor system, check that the VRM is not
plugged into the terminator socket.

The error message could also show: Power
CPU1 and Power CPU2.

Test of the correct power signals
to the CPU. The power supply
may be OK, whereas the VRM is
not.

POWER

Check that the VRM, processor and
terminator are correctly
installed.

Check that the VRM is not plugged on a
socket with a
terminator (this could be the likely cause).

Check or replace the VRM.

Check the power supply unit connectors.

Presence of VRMs and their
associated processor.

POWER CPU

Check that the VRMs are correctly installed
in their VRM
sockets.
POWER CPU 1 - Check VRMs sockets 1 and
2.
POWER CPU 2 - Check VRM socket 3.
POWER CACHE - Check VRM socket 2.

Presence of a VRM in VRM
socket 2. This test is for both
single and dual processor
systems.

POWER
CACHE

Check that the VRM is correctly installed in
VRM socket 2.

Check the system board clock
generators (PLL).

BOARD PLL

Check the power supply connector.

Replace the system board (PLL clock
generator).

Содержание X Class 500/550MHz






















































































































































Результаты поиска

Содержание X Class 500/550MHz

Отзывы:

Похожие инструкции для X Class 500/550MHz

Бренды по названию

Популярные бренды

HP X Class 500/550MHz, Справочное руководство

Результаты поиска

Содержание X Class 500/550MHz

Отзывы:

Похожие инструкции для X Class 500/550MHz

Бренды по названию

Популярные бренды