HP X Class 500/550MHz Скачать руководство пользователя страница 115 | Manualshive

Страница: 115 / 149

background image

Chapter 5

115

Tests and Error Messages

MaxiLife Test Sequence and Error Messages

Operating System Boot Phase

If no error message has been displayed at this stage of the system start-up by the BIOS,
the operating system is launched and the LCD status panel will display the system
platform and a “smiling icon.”

Run-Time Errors

During the normal usage of the Personal Workstation, MaxiLife continually checks some of
the vital system parameters. These include: temperature errors, fan malfunctions, power
voltage drops, board PLL problems and CPU problems.

If several alarms or errors are active at the same time, they will be displayed by cycling
every second through four “alarm sources”, with one error cause for each source:

• Pre-boot diagnostics.

• Run-Time error 1.

• Run-Time error 2.

• POST error.

The run-time errors are organized into two different sources.

Run-Time error 1: “Temperature I/O slot”, “Power errors”, “Fan CPU”, “Board PLL”.

Run-Time error 2: “Temperature disk”, “Temperature CPU”, “Fan disk”, “Fan I/O slot”,
“CPU error”.

If both fan for disks and I/O slot are not connected (both are run-time error 1), only the
“Fan disk” (run-time error 2) will be displayed.

Main Menu

The main menu is displayed when any of the LCD buttons from are pressed (MaxiLife
LCD status panel can be accessed even though the Personal Workstation is turned off).
The Main menu comprises of three sub-menus: System Info, Boot Steps and Diagnostics.

Table 5-3. Run-Time Errors

Test

Error Code

Action to Take

During normal usage of the
Personal Workstation, HP
MaxiLife continually checks vital
system parameters. If an error
should occur, a message would be
automatically displayed on the
LCD panel.

FAN CPU

Check the connection of the corresponding
component, which could be: “Temp IO slot”,
“Power errors, “Fan CPU”, “Board PLL”,
“Temp disk”, “Temp CPU”, “Fan disk”, “Fan

IO slot”, “CPU error”.

1

1. Special cases: Board PLL = System board needs replacing. CPU error = Reset or power off

the system to recover.

«
...
113
114
115
116
117
...
»

Содержание X Class 500/550MHz






















































































































































Отзывы:

Нет отзывов

Похожие инструкции для X Class 500/550MHz

Бренд: NEC Страницы: 7

Бренд: D-Link Страницы: 6

Бренд: D-Link Страницы: 16

Бренд: D-Link Страницы: 16

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 12

Бренд: D-Link Страницы: 32

Бренд: D-Link Страницы: 5

Бренд: D-Link Страницы: 45

Бренд: D-Link Страницы: 3

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 18

Бренд: D-Link Страницы: 24

Бренд: D-Link Страницы: 32

ThermoVu DTM-500

Бренд: Digital-Ally Страницы: 31

Бренд: Supermicro Страницы: 21

Бренд: Pandigital Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды