HP X Class 500/550MHz Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 149

background image

Chapter 1

21

System Overview

Front Panel

Front Panel

This section explains the HP V

ISUALIZE

Personal X-Class Workstation’s front panel features.

Figure 1-3. Front Panel Features of the Personal Workstation

NOTE

The front panel volume control that was available on previous generations of
the HP V

ISUALIZE

Personal Workstations has been removed. Volume can now

be controlled using the keyboard or the software volume control.

Table 1-2. Front Panel Features and Their Descriptions

Liquid Crystal Display (LCD)

The MaxiLife control panel menus are described in detail in the section “MaxiLife
Architecture” in the chapter “System Board.”

PC Lock Button

This button has the same functionality as the multimedia keyboard “lock key.” When
HP Lock is installed under Windows NT 4.0, pressing this button is equivalent to “NT
Lock Workstation.” If HP Lock is not install, then this feature will not work.

On/Off LED

This light has four states:

Blank

Indicates that the computer is off.

Green

Indicates that the computer is turned on and running
correctly.

Red

Indicates that there is a Power-On Self-Test (POST)
error. Red flashing indicates that there is a MaxiLife
(Diag/Alarm) error.

Amber

Indicates a system reset, system lock, standby mode
(Windows 98) or suspend mode (Windows 95).

Hard Disk Drive Activity
LED

This light is active during POST and when the hard disk drive is being accessed.

LAN Activity LED

This light is active when the Personal Workstation is accessing the network. For this
feature to work, specific LAN HP drivers need to be installed.

Lock LED (Amber)

This light is displayed when the system is locked.

Hard Disk Activity Light

Network Activity Light

MaxiLife LCD
Control Buttons

Power On/Off
Button and LED

Reset Button

PC Lock Button
and LED

«
...
19
20
21
22
23
...
»

Содержание X Class 500/550MHz






















































































































































Отзывы:

Нет отзывов

Похожие инструкции для X Class 500/550MHz

Бренд: U.S. Boiler Company Страницы: 20

HandyTone-286 Rev 3.0

Бренд: Grandstream Networks Страницы: 12

TravelCharge Companion HT 3.4

Бренд: Wagan Страницы: 16

Бренд: Agilent Technologies Страницы: 32

Бренд: Lanpro Страницы: 27

Бренд: StarTech.com Страницы: 2

F8T031 - Bluetooth Wireless USB Printer Adapter Print Server

Бренд: Belkin Страницы: 93

Бренд: TP-Link Страницы: 18

Бренд: Monster Страницы: 2

Xcomfort CSAP-01/0 Series

Бренд: Moeller Страницы: 4

Бренд: Zonet Страницы: 19

Бренд: BeachTek Страницы: 2

Бренд: Danfoss Страницы: 166

Бренд: D-Link Страницы: 7

Бренд: D-Link Страницы: 30

Бренд: D-Link Страницы: 25

DUB-9240 - UWB Wireless USB

Бренд: D-Link Страницы: 16

Бренд: D-Link Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды