HP X Class 500/550MHz Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 149

background image

Chapter 2

43

System Board

Chipset

PCI to ISA/EIO Bridge

PIIX4E compatible with the PCI Rev. 2.1 specification, as well as the IEEE 996
specification for the ISA (AT) bus. On PCI, PIIX4E operates as a master for various
internal modules, such as the USB controller, DMA controller, IDE bus master controller,
distributed DMA masters, and on behalf of ISA masters. PIIX4E operates as a slave for its
internal registers or for cycles that are passed to the ISA or EIO buses.

ISA Bus Interface

As well as accepting cycles from the PCI bus interface, and translating them for the ISA
bus, the ISA bus interface also requests the PCI master bridge to generate PCI cycles on
behalf of a DMA or ISA master. The ISA bus interface contains a standard ISA bus
controller and data buffering logic. Refer to the section “Devices on the ISA Bus” in this
chapter for a description of the devices on the ISABus.

SMBus Controller

The System Management (SM) bus is a two-wire serial bus provided by the PIIX4E
controller. It runs at a maximum of 16 kHz. The SMBus Host interface allows the CPU to
communicate with SMBus slaves and an SMBus Slave interface that allows external
masters to activate power management events. The bus also monitors some of the
hardware functions of the main board, both during boot-up and run-time. All accesses to
the bus are handled by the main processor, via the PIIX4E SMBus registers. Refer to the
section “Devices on the SMBus” for a description of the devices on the SMBus, or to the
section “HP MaxiLife Utility” in this chapter for information on the MaxiLife ASIC.

IDE Controller

The PCI master/slave IDE controller (Bus Master capability and synchronous DMA mode),
supporting two devices is described in the section “Integrated Drive Electronics (IDE)” in
this chapter.

Timers Based on 82C54

• System Timer, Refresh Request, Speaker

Tone Output.

SMBus

• Host Interface allows CPU to communicate

via SMBus.

• Slave interface allows external SMBus

Master to control
Resume Events.

324 mBGA Package

Table 2-3. PIIX4E (82371EB) Chip Features

Feature

Feature

«
...
41
42
43
44
45
...
»

Содержание X Class 500/550MHz






















































































































































Отзывы:

Нет отзывов

Похожие инструкции для X Class 500/550MHz

Бренд: Paradyne Страницы: 2

Бренд: spirit of gamer Страницы: 65

Бренд: comPPage Страницы: 38

Бренд: Qlogic Страницы: 8

Бренд: Rocstor Страницы: 2

HM-LC-Dim1L-Pl-2

Бренд: HomeMatic Страницы: 15

Baby Trend Expedition U-shaped Support Bar (facing up)Baby Trend Flex LocBaby Trend GabriellaBaby Trend Stride SportBaby

Бренд: Baby Jogger Страницы: 5

Бренд: Modecom Страницы: 24

Powerline Adaptor Kit

Бренд: NETGEAR Страницы: 8

Бренд: Hainbuch Страницы: 108

Бренд: M&S Systems Страницы: 4

Бренд: Atlantis Страницы: 24

Бренд: Digital Equipment Страницы: 74

Бренд: nedis Страницы: 2

Бренд: nedis Страницы: 2

Бренд: nedis Страницы: 2

Бренд: Kvaser Страницы: 24

Бренд: Edimax Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды