HP X Class 500/550MHz Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 149

background image

Chapter 2

37

System Board

Chipset

Chipset

The Intel® 440GX AGPset chipset is comprised of the 82443GX Host Bridge/Controller
and, the 82371EB (PIIX4E) chip, which is a highly integrated version of the Intel PCI-ISA
bridge family for the I/O subsystem.

• The Host Bridge, also referred to as the North Bridge, is the bridge between four buses:

the Front Side Bus (FSB), the main memory (SDRAM) bus, the PCI bus and the AGP
(graphic) bus.

• The PIIX4E chip, also referred to as the South Bridge, is the bridge between three

buses: the PCI bus, the SMBus and the ISA bus. In addition, it contains the IDE
controller, USB controller and Power Management logic, Interrupt controller, Real Time
Clock (RTC) and CMOS. The table “PIIX4E (82371EB)” in this chapter details the
PIIX4E chip features.

Host Bridge/Controller (82443GX)

The Host Bridge/Controller is contained in a 492-pin Ball Grid Array (BGA) package. The
following table shows the features that are available in the Host Bridge/Controller.

Table 2-2. Features Available in the Host Bridge/Controller

Feature

Feature

Processor/Host Bus Support

• Optimized for Pentium® processor at: 100

MHz system bus frequency.

• Supports full Symmetric Multiprocessor

(SMP) Protocol for up to two processors; I/O
APIC related buffer management support
(WSC# signal).

• In-order transaction and dynamic deferred

transaction support.

• Desktop

optimized

GTL+

bus

driver

technology

(gated

GTL+

receivers

for

reduced power).

AGP Interface

• Supports

single

AGP-compliant

device

(AGP-66/133 3.3V
device).

• AGP Specifications Rev. 1.0 compliant.

• AGP-data/transaction

flow

optimized

arbitration mechanism.

• AGP side-band interface for efficient request

pipelining without interfering with the data
streams.

• AGP-specific data buffering.

• Supports concurrent CPU, AGP and PCI

transactions to main memory.

• AGP high-priority transactions (“expedite”)

support.

«
...
35
36
37
38
39
...
»

Содержание X Class 500/550MHz






















































































































































Отзывы:

Нет отзывов

Похожие инструкции для X Class 500/550MHz

Бренд: powerpack Страницы: 9

Бренд: Intermec Страницы: 2

Бренд: Lindy Страницы: 12

Бренд: Jabra Страницы: 3

Бренд: Hainbuch Страницы: 64

Бренд: StarTech.com Страницы: 2

PEPWAVE MAX Adapter

Бренд: peplink Страницы: 20

Бренд: MSI Страницы: 162

Бренд: Belkin Страницы: 165

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 24

Бренд: D-Link Страницы: 82

Бренд: D-Link Страницы: 23

DHP-303 - PowerLine HD EN Starter

Бренд: D-Link Страницы: 29

Бренд: D-Link Страницы: 28

Бренд: D-Link Страницы: 49

Бренд: D-Link Страницы: 60

Бренд: D-Link Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды