HP X Class 500/550MHz Скачать руководство пользователя страница 143 | Manualshive

Страница: 143 / 149

background image

Appendix A

143

Regulatory Information and Warranty

HP Hardware Warranty

from date of purchase. This service will also provide technical assistance with the basic
configuration and setup of your HP V

ISUALIZE

Personal Workstation and for the bundled or

pre-loaded operating system.

Telephone support is available at the end of the first year from date of purchase, via the
Lifeline program, which is a fee-based service (North America and Europe only).

HP does NOT provide telephone support for Personal Workstations configured as network
servers. We recommend HP NetServers for your network server requirements.

(Rev. 17/03/98)

HP Software Product License Agreement and Software Product
Limited Warranty

Your HP V

ISUALIZE

Personal Workstation contains preinstalled software programs. Please

read the Software License Agreement before proceeding.

CAREFULLY READ THIS LICENSE AGREEMENT AND LIMITED WARRANTY
STATEMENT BEFORE PROCEEDING TO OPERATE THIS EQUIPMENT. RIGHTS IN
THE SOFTWARE ARE OFFERED ONLY ON THE CONDITION THAT THE
CUSTOMER AGREES TO ALL TERMS AND CONDITIONS OF THE LICENSE
AGREEMENT. PROCEEDING TO OPERATE THE EQUIPMENT INDICATES YOUR
ACCEPTANCE OF THESE TERMS AND CONDITIONS. IF YOU DO NOT AGREE WITH
THE TERMS OF THE LICENSE AGREEMENT, YOU MUST NOW EITHER REMOVE
THE SOFTWARE FROM YOUR HARD DISK DRIVE AND DESTROY THE MASTER
DISKETTES, OR RETURN THE COMPLETE COMPUTER AND SOFTWARE FOR A
FULL REFUND.

PROCEEDING WITH CONFIGURATION SIGNIFIES YOUR ACCEPTANCE OF THE
LICENSE TERMS.

HP Software Product License Agreement

UNLESS OTHERWISE STATED BELOW, THIS HP SOFTWARE PRODUCT LICENSE
AGREEMENT SHALL GOVERN THE USE OF ALL SOFTWARE THAT IS PROVIDED
TO YOU, THE CUSTOMER, AS PART OF THE HP COMPUTER PRODUCT. IT SHALL
SUPERSEDE ANY NON-HP SOFTWARE LICENSE TERMS THAT MAY BE FOUND
ON-LINE, OR IN ANY DOCUMENTATION OR OTHER MATERIALS CONTAINED IN
THE COMPUTER PRODUCT PACKAGING.

Note: Operating System Software by Microsoft is licensed to you under the Microsoft End
User License Agreement (EULA) contained in the Microsoft documentation.

The following License Terms govern the use of the software:

USE. Customer may use the software on any one computer. Customer may not network the
software or otherwise use it on more than one computer. Customer may not reverse
assemble or decompile the software unless authorized by law.

COPIES AND ADAPTATIONS. Customer may make copies or adaptations of the software
(a) for archival purposes or (b) when copying or adaptation is an essential step in the use of
the software with a computer so long as the copies and adaptations are used in no other
manner.

«
...
141
142
143
144
145
...
»

Содержание X Class 500/550MHz






















































































































































Отзывы:

Нет отзывов

Похожие инструкции для X Class 500/550MHz

Бренд: H3C Страницы: 37

Bluetooth USB-Adapter Version 1.2

Бренд: Hama Страницы: 8

Бренд: RocketFish Страницы: 15

Бренд: Davis Instruments Страницы: 4

Бренд: 4B Страницы: 29

Бренд: Sabrent Страницы: 4

Бренд: Panda Wireless Страницы: 10

Бренд: Mellanox Technologies Страницы: 42

Smart Wireless THUM Adapter

Бренд: Emerson Страницы: 28

Бренд: Emerson Страницы: 48

Smart Wireless THUM Adapter

Бренд: Emerson Страницы: 62

FM 5 IN DASH ADAPTER KIT

Бренд: Eagle Страницы: 5

Бренд: oticon Страницы: 54

Artisan 700 Series

Бренд: Epson Страницы: 2

Artisan 800 - All-in-One Printer

Бренд: Epson Страницы: 106

Artisan 700 Series

Бренд: Epson Страницы: 40

ActionTower 3000 Computer

Бренд: Epson Страницы: 137

Artisan 700 Series

Бренд: Epson Страницы: 145

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды