HP X Class 500/550MHz Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 149

background image

44

Chapter 2

System Board

Chipset

Enhanced USB Controller

The USB (Universal Serial Bus) controller provides support for the Universal Host
Controller Interface (UHCI). This includes support that allows legacy software to use a
USB-based keyboard and mouse. The USB supports two stacked connectors on the back
panel. These ports are built into the PIIX4E controller, as standard USB ports. The USB is
described in detail in the section “Universal Serial Bus (USB) Controller” in this chapter.

DMA Controller

The seven-channel DMA controller incorporates the functionality of two 82C37 DMA
controllers. Channels 0 to 3 are for 8-bit DMA devices, while channels 5 to 7 are for 16-bit
devices (see the section “DMA Channel Controllers” in the chapter “HP BIOS”). The
channels can be programmed for any of the four transfer modes: the three active modes
(single, demand, block) can perform three different types of transfer: read, write and verify.
The address generation circuitry supports a 24-bit address for DMA devices.

Interrupt Controller

Based on two 82C59 interrupt controllers. The two interrupt controllers are cascaded so
that 14 external and two internal interrupts are possible. In addition, PIIX4E supports a
serial interrupt scheme. It also supports the onboard I/O APIC controller 82093AA. A table
in the section “Interrupt Controllers” in the chapter “HP BIOS” shows how the master and
slave controllers are connected.

Counter / Timer

The chip contains a three-channel 82C54 counter/timer. Three counters are combined to
provide the system timer function, refresh request, and speaker tone. The counters use a
division of the 14.318 MHz OSC input as the clock source.

Serial EEPROM

This is the non-volatile memory which holds the values for the Setup program (they are no
longer stored in the CMOS memory). The Serial EEPROM is described in the section
“Serial EEPROM” in this chapter.

«
...
42
43
44
45
46
...
»

Содержание X Class 500/550MHz






















































































































































Отзывы:

Нет отзывов

Похожие инструкции для X Class 500/550MHz

AirStation WLI-U2-SG54HG

Бренд: Buffalo Страницы: 136

Бренд: Vigor Страницы: 6

Бренд: Vantec Страницы: 5

Бренд: Edimax Страницы: 30

Бренд: Airlink101 Страницы: 47

Бренд: Conrad Страницы: 2

1520A - AHA Storage Controller Fast SCSI 10 MBps

Бренд: Adaptec Страницы: 62

Бренд: XIMEA Страницы: 23

Бренд: TRENDnet Страницы: 18

Бренд: KSH International Страницы: 18

Бренд: TP-Link Страницы: 75

Бренд: Sailor Страницы: 25

Бренд: ZyXEL Communications Страницы: 2

Бренд: Eusso Страницы: 30

Бренд: CREVIS Страницы: 8

Бренд: MUKii Страницы: 24

Бренд: Q-DIS Страницы: 4

Бренд: Supra Страницы: 183

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды