HP rp7400 Скачать руководство пользователя страница 112

Страница: 112 / 162

SCSI Devices

112

Default ID = 7

2. Press

<Return>

Example 1

Display

SCSI transfer rate for a controller at 0/0/2/0 (Internal drive path)

Command:

SCSI RATE <0/0/2/0>

Response:

Path (dec)

Initiator ID

SCSI Rate

----------

------------

---------

0/0/2/0

No Limit

Example 2

Set

the SCSI transfer rate for a controller at 0/0/2/0 to Ultra II

Command:

SCSI RATE 0/0/2/0 0

Response:

Path (dec)

SCSI Rate

---------- ---------
0/0/2/0

No Limit

Example 3

Display

SCSI initiator ID for

all

controllers, busses, and slots.

* Shows all controllers and Id's that have been programmed.SCSI controllers that are in PCI slots that have
not been altered from default will not show up. Only core controllers are displayed until the other slots are
programmed.

4.Set the SCSI initiator ID of a controller at 0/0/2/1

Command:

SCSI

Response:

Path (dec)

Initiator ID

SCSI Rate

------------

--------------

----------

0/0/2/0

Ultra

0/0/2/1

Ultra

0/0/1/0

No Limit

5/0/0

Fast

12/0/0

Fast

12/0/1

Fast

0/0/10/0/0

Unknown

0/0/10/0/1

Unknown

0/0/12/0/0

Unknown

0/0/12/0/1

Unknown

0/8/0/0

No Limit

0/8/0/1

No Limit

Example 4

Sets

the SCSI initiator ID for a specified controller, bus, and slot.

Command:

SCSI init 0/0/2/1 6

Response:

Path (dec)

Initiator ID

----------

-------------

0/0/2/1

Содержание rp7400



































































































































































Результаты поиска

Содержание rp7400

Отзывы:

Похожие инструкции для rp7400

Бренды по названию

Популярные бренды

HP rp7400, Руководство по оборудованию

Результаты поиска

Содержание rp7400

Отзывы:

Похожие инструкции для rp7400

Бренды по названию

Популярные бренды