manualshive.com logo in svg

HP rp7400, Руководство по оборудованию, Страница: 95 / 162

Поделиться
Скачать
HP rp7400 Скачать руководство пользователя страница 95

 

95

HP 700 Series System Console Configuration

The following describes the steps required to configure the HP 700 series terminal for VT-100 mode for 
operation with the rp7400 server.

Although any terminal capable of operating in VT-100 mode can be used, the HP700 series terminal is used 
here as an example because it is fairly common and it’s configuration is typical of many terminals currently in 
use.

HP700 VT-100 Mode Configuration

The following procedure outlines the steps to configure the HP700 series terminal for VT-100 operation. 

NOTE

You may use either the arrow keys or the tab key to move between the setting options on the 
screen.

1. Press 

[config keys]

 function key. 

[f8]

2. Press 

[terminal config]

 function key. 

[f5]

3. Move to 

Terminal ID

 and enter “vt100”.

4. Move to 

Set TermMode

 and, using the 

[Prev]

 and 

[Next]

 keys, select “EM100”.

5. Press the 

[config keys]

 function key

. [f8]

6. Press the

 [ansi config]

 function key

. [f6]

7. Move to “multipage” and, using the 

[Prev]

 and 

[Next]

 keys, select “yes”. 

(Enables screen scrolling).

8. Move to 

Backspace Del

 and, using the 

[Prev]

 and 

[Next]

 keys, select “Backspace/Del”.

9. Move to 

EM100 ID

 and, using the 

[Prev]

 and 

[Next]

 keys, select “EM100”.

Содержание rp7400



































































































































































Отзывы:

Нет отзывов