HP rp7400 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 162

HP rp7400 Скачать руководство пользователя страница 19

rp7400 Enterprise Server System Safety and Regulatory Information

19

FCC Statement (USA Only)

The United States Federal Communications Commission has specified that the following notice be brought to
the attention of users of this product:

NOTE

This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.

Hewlett-Packard's system verification tests were conducted with HP-supported peripheral devices and HP
shielded cables, such as those you receive with your computer. Changes or modifications not expressly
approved by Hewlett-Packard could void the user's authority to operate the equipment. Cables used with this
device must be properly shielded to comply with the requirements of the FCC.

Canada RFI Statement

This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations.

Notice relative aux interférences radioélectriques (Canada)

Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur
du Canada.

European Union RFI Statement

This is a Class A product. In a domestic environment, this product may cause radio interference in which case
the user may be required to take adequate measures.

«
...
17
18
19
20
21
...
»

Содержание rp7400



































































































































































Отзывы:

Нет отзывов