HP rp7400 Скачать руководство пользователя страница 146

Страница: 146 / 162

Adding a Disk Drive to an HP-UX System

144

# pvcreate -B /dev/rdsk/cXtXdX

Step 3.

Create a directory for the volume group using

mkdir

Step 4.

Create a device file named group in the above directory with the

mknod

command.

Step 5.

Create the root volume group specifying each physical volume to be included using

vgcreate

. For

example:

vgcreate /dev/vgroot /dev/dsk/cXtXdX

Step 6.

Use

mkboot

to place boot utilities in the boot area:

mkboot /dev/rdsk/cXtXdX

Step 7.

Use

mkboot -a

to add an

AUTO

file in boot

LIF

area, for example:

mkboot -a ‘’hpux (52.3.0;0)/stand/vmunix’’ /dev/rdsk/cXtXdX

Step 8.

Create the root logical volume. You must specify contiguous extents (

-C y

) with bad block relocation

disabled (

-r n

). For example,

lvcreate -C y -r n root /dev/vgroot

Step 9.

Extend the mirrors onto the disk you’ve added. For example:

lvextend -m 1 <LV name> /dev/vgroot/root /dev/dsk/cXtXdX

Step 10.

Specify that logical volume be used as the root logical volume, for example:

lvln -r /dev/vgroot/root

At this point you will need to create a file system on the disk. Refer to your HP-UX system administration
documentation.

Hot Swap Procedure for Unattached Physical Volumes

Follow these steps to replace a hot swap disk drive for unattached physical volumes.

NOTE

HP often uses different manufacturers for disks having the same product number. This hot
swap procedure will not automatically update the disk driver’s internal manufacturer
information to that of the added disk drive.

Step 1.

Do an

ioscan

on the replaced disk drive to ensure that it is accessible an also as a double check that

it is a proper replacement. Refer to the above note. For example:

# ioscan /dev/dsk/c2t4d0

Содержание rp7400



































































































































































Результаты поиска

Содержание rp7400

Отзывы:

Похожие инструкции для rp7400

Бренды по названию

Популярные бренды

HP rp7400, Руководство по оборудованию

Результаты поиска

Содержание rp7400

Отзывы:

Похожие инструкции для rp7400

Бренды по названию

Популярные бренды