manualshive.com logo in svg

HP rp7400, Руководство по оборудованию

Поделиться
Скачать
HP rp7400 Скачать руководство пользователя страница 132

rp7400 Server Boot up

132

3.

Many

 selftest boot progress screens will be displayed. These will scroll rapidly up the screen. Some tests 

may pause for up to one minute while the test completes.

The following abbreviated examples of the forward progress screens are typical of the screens displayed.

GSP Host Name: <HostName>

GSP>
********** VIRTUAL FRONT PANEL **********

System Boot detected
*****************************************
platform

config

626F

processor

slave rendezvous

1C17

processor

test

1142

processor

test

1100

processor

test

1100

processor

test

1100

processor

test

1100

processor

test

1100

processor

test

1100

processor

test

1100

processor

test

1100

processor INIT

1701

processor

test

1120

processor

slave rendezvous

1C40

processor

test

1142

processor

test

113B

platform

test

612A

I/O

config

8238

*****************************************
*************EARLY BOOT VFP *************

End of early boot detected
*****************************************
Firmware Version  XX.XX
Duplex Console IO Dependent Code (IODC) revision 1
--------------------------------------------------------------------------
(c) Copyright 1995-1998, Hewlett-Packard Company, All rights reserved
--------------------------------------------------------------------------

Processor Speed State

CoProcessor State

Cache

Size

Number State

Inst

Data

-------

-------

----------------

-----------------  ----

-----

1

440 MHz

Active

Functional

512 KB

1 MB

3

440 MHz

Idle

Functional

512 KB

1 MB

Central Bus Speed (in MHz) :

120

Available Memory

:

2752512 KB

Good Memory Required

:

10304  KB

Primary boot path:    0/0/2/0.6
Alternate boot path:  0/0/2/1.6
Console path:         0/0/4/0.0
Keyboard path:        0/0/4/0.0

WARNING:  Memory subsystem address parity checking is disabled.
This has been disabled via a NVM control bit.  This may have 
been set manually.  Or it may have been set automatically if 
this system has 64 MB DIMMs,  which do not consistently return
proper address parity. 

Processor is booting from first available device.
To discontinue, press any key within 10 seconds.
Boot terminated.

Содержание rp7400



































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды