HP rp7400 Скачать руководство пользователя страница 157 | Manualshive

Страница: 157 / 162

background image

Add I/O Cards

155

Add I/O Cards

The rp7400 server has 12 expansion I/O slots accessible through side panels on the rear of the SPU chassis.
Six slots are located on each of the two sides.

Slots 3 through 12 are “TwinTurbo” slots supporting 66MHz, 64-bit I/O cards. Slots 1 and 2 are “Turbo” slots
supporting cards with lower speed and bandwidth. If higher speed cards are installed in slots 1 or 2, they will
function but their performance will be reduced. Similarly, slower cards can be installed in slots 3 through 12,
but their performance will not be improved.

There are two configuration rules to consider:

•

Load the slowest cards in slots 1 and 2.

•

When possible, balance the total number of PCI cards between the two sides. E.g., when adding four PCI
cards, install two on the right (slots 1 through 6) and two on the left (slots 7 through 12).

CAUTION

If you are installing the A3783A 10/100Base-TX LAN card, do not connect any type of MAU
transceiver to the AUI connector while the system is powered up. Doing so will cause power to
be shut off to the I/O slot and will generate a High Priority Machine Check (HPMC) error.

If you are going to connect a MAU transceiver to this card’s AUI connector, make sure the
system is powered down first. When the system is powered back on, this connection will then
not generate an error condition.

Refer to the instructions shipped with this LAN card for further information.

Procedure Overview

1. Remove power from the system

2. Remove the front bezel

3. Extend the SPU out the back of the system

4. Remove the PCI slot cover

5. Insert the new PCI card

6. Replace the PCI slot cover

7. Slide the SPU back into the cabinet

8. Replace the front bezel

9. Power the system back on

10. Verify the procedure

«
...
155
156
157
158
159
...
»

Содержание rp7400



































































































































































Отзывы:

Нет отзывов

Похожие инструкции для rp7400

Бренд: Campden instruments Страницы: 8

Бренд: HABYS Страницы: 16

Бренд: VBM Страницы: 36

Бренд: W&H Med Страницы: 122

Бренд: KCI Страницы: 2

Бренд: KCI Страницы: 60

Бренд: Landoll Страницы: 38

Бренд: Additel Страницы: 107

CIRCOLINA G10q T9

Бренд: Life Страницы: 2

LUNAQUA Classic LED

Бренд: Oase Страницы: 16

Бренд: Kamar Страницы: 2

TR 2B INC INT NC

Бренд: OMGA Страницы: 76

Бренд: ABS Страницы: 17

Бренд: American DJ Страницы: 8

Sure Stripe 3650

Бренд: AIRLESSCO Страницы: 14

Бренд: Civemasa Страницы: 55

Бренд: Heitronic Страницы: 16

Бренд: Ocean Sonics Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды