HP rp7400 Скачать руководство пользователя страница 34

Страница: 34 / 162

Verify system complicity with regulatory standards

21.

Are the input circuit breakers adequate for equipment loads?

Safety

No.

Area or condition

Yes

22.

Is there an emergency power shut-off switch?

23.

Is there a telephone available for emergency purposes?

24.

Is there a fire protection system in the computer room?

25.

Is antistatic flooring installed?

26.

Are there any equipment servicing hazards?

27.

Are the proper tools and installation equipment available?

Cooling

No.

Area or condition

Yes

28.

Can cooling be maintained between 54

and 86

(20

and 30

C)?

29.

Can temperature changes be held to less than 10

C per hour?

30.

Can humidity level be maintained between 40% and 60%?

31.

Are air conditioning filters installed?

Storage

No.

Area or condition

Yes

32.

Are cabinets available for tape and disc media?

33.

Is shelving available for documentation?

Training

No.

Area or condition

Yes

33.

Are personnel enrolled in the System Administrator’s Course?

34.

Is on-site training needed?

Table 3

(Continued)

Содержание rp7400



































































































































































Результаты поиска

Содержание rp7400

Отзывы:

HP rp7400, Руководство по оборудованию, Страница: 34 / 162

Результаты поиска

Содержание rp7400

Отзывы: