HP rp7400 Скачать руководство пользователя страница 97

Страница: 97 / 162

Core I/O Connections and Indicators

The following paragraphs describe the operator indicators and Core I/O connections at the rear of the rp7400.

(Green) Core I/O board Power LED

- When lit indicates that the Core I/O board has DC power available.

(Green) Guardian Service Processor Power LED

- When lit indicates that the Guardian Service Processor

has DC power available.

(Red) Failed Self-Test LED

- When lit, indicates that one or more power-up self tests has failed.

(Amber) 10BASE-T Console LAN Collision LED

- When lit, indicates that a data packet collision has

occurred on the 10BASE-T LAN Console LAN.

(Green) 10BASE-T Console LAN Link OK LED

- When lit, indicates that the 10BASE-T Console LAN

Link status is OK.

(Green) 10BASE-T Console LAN Receive LED

- When lit, indicates that a data packet has been received

over the 10BASE-T Console LAN.

(Green) 10BASE-T Console LAN Transmit LED

- When lit, indicates that a data packet has been

transmitted over the 10BASE-T Console LAN.

(Green) 10BASE-T/100BASE-T Mode LED

- When lit, indicates that the LAN is in 100 Mbps Mode.

When unlit, indicates that the LAN is in 10 Mbps Mode.

(Amber) 10BASE-T/100 BASE-T LAN Collision LED

- When lit, indicates that a data packet collision has

occurred on the 10BASE-T/100BASE-T LAN.

10.

(Green) 10BASE-T/100BASE-T LAN Link OK LED

- When lit, indicates that the 10BASE-T/100BASE-T

LAN Link status is OK.

11.

(Green) 10BASE-T/100 BASE-T LAN Receive LED

- When lit, indicates that a data packet has been

received over the 10BASE-T/100BASE-T LAN.

12.

(Green) 10BASE-T/100 BASE-T LAN Transmit LED

- When lit, indicates that a data packet has been

transmitted over the 10BASE-T/100BASE-T LAN.

13.

(Green) Differential Sense (Diffsens) LED

- When Lit, indicates that the external SCSI bus is in

Low

Voltage Differential

mode. When Unlit indicates the external SCSI bus is in

Single-Ended

mode.

14.

(Green) Terminator Power (Termpower) LED

- When Lit, indicates that SCSI terminator power is being

supplied by the rp7400. When unlit, indicates that SCSI terminator power is being supplied by the
external SCSI device.

Содержание rp7400



































































































































































Результаты поиска

Содержание rp7400

Отзывы:

HP rp7400, Руководство по оборудованию, Страница: 97 / 162

Результаты поиска

Содержание rp7400

Отзывы: