manualshive.com logo in svg

HP rp7400, Руководство по оборудованию

Поделиться
Скачать
HP rp7400 Скачать руководство пользователя страница 145

 

Adding a Disk Drive to an HP-UX System

143

Adding a Disk Drive to an HP-UX System

The internal disk drives (A upper and B lower) are located in the back of the SPU. The internal disk drives are 
hot swapable when the proper software and hardware procedures are followed.

To add a disk drive in the SPU, perform the following hardware steps:

1. Align the new disk drive into the disk tray and insert the four (2 on each side) mounting screws to secure 

the disk to the tray.

2. Align the disk and tray assembly to the empty slot in the back of the SPU. 

3. Carefully slide the disk into the SPU until it firmly seats into the disk card. Note that the guide tabs on 

each side of the disk tray fully seat to the guide pins on the chassis.

4. Angle the bottom of the disk cover plate into the SPU so that the hooked tabs go over the extended pins 

inside the chassis. This acts like a hinge for the cover. 

5. Push the top of the cover plate towards the SPU until it is flush with the chassis and fully seated.

6. Tighten the single, captive mounting screw.

To view the video, 

click here

.

Once you have completed the addition of the disk drive, you must perform the Hot swap procedure:

Hot Swap Software Procedure

NOTE

HP often uses different manufacturers for disks having the same product number. This hot 
swap procedure will not automatically update the disk driver’s internal manufacturer 
information to that of the added disk drive.

Step 1.

Do an 

ioscan

 on the added disk drive to ensure that it is accessible an also as a double check that it 

is a proper installation. Refer to the above note. For example:

# ioscan /dev/dsk/cXtXdX 

Step 2.

Create a physical volume using pvcreate with the -B option. -B creates an area on the disk for a LIF 
volume, boot utilities, and a BDRA (Boot Data Reserved Area). For example,

Содержание rp7400



































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды