HP rp7400 Скачать руководство пользователя страница 156 | Manualshive

Страница: 156 / 162

background image

Add-On Memory

154

Step 12. Replace the Front Bezel

To replace the front bezel, perform the following steps:

a.

Align the front bezel over the front of the SPU.

b.

Press the front bezel onto the cabinet until it snaps into place.

Step 13. Power the System On

CAUTION

Before applying A.C. power to an rp7400 computer, be sure all covers and cooling
fans are properly installed. Failure to perform this check could result in decreased
computer component life and reliability.

a.

Be sure all connected peripherals are on, with no errors or faults indicated.

b.

Be sure the SPU power switch is in the standby (0) position.

CAUTION

When the power cords are connected to the SPU, there will be power present
inside the SPU chassis, even with the power switch in the standby position.

c.

Carefully insert the A.C. power cords (3) into the line filter receptacles at the back of the SPU.

NOTE

Be sure to plug all three power cords into the back of the SPU. Also be sure the
cabinet PDU is plugged into an appropriate wall outlet.

d.

Put the power switch in the on (|) position. At this time you will hear the cooling fans coming up
to speed and being synchronized. This creates a high pitched squeak for a few seconds. The fans
should drop to normal speed within a few seconds. If not check the front panel or console for
fault indications.

e.

Check all front panel LEDs for normal indications, with no warnings ar faults indicated.

The SPU should take a few minutes to perform all selftests and initialization routines. At the end of
this you should be able to launch the operating system or initiate other software routines.

Step 14. Verify the Installation

Issue the

ME

command in the boot console handler to verify the system recognizes the new memory

configuration.

«
...
154
155
156
157
158
...
»

Содержание rp7400



































































































































































Отзывы:

Нет отзывов

Похожие инструкции для rp7400

Бренд: Calistair Страницы: 44

Бренд: zipwake Страницы: 2

Бренд: zipwake Страницы: 2

Бренд: Daktronics Страницы: 30

Бренд: DAKOTA ULTRASONICS Страницы: 28

Бренд: TEC Страницы: 6

Бренд: U Technology Страницы: 6

Бренд: Ultimate Healthcare Страницы: 2

Бренд: Ultimate Healthcare Страницы: 40

MCX-C15 - MusicCAST Network Audio Player

Бренд: Yamaha Страницы: 65

Бренд: Yamaha Страницы: 24

TOTAL KNEE 1900

Бренд: Össur Страницы: 58

Бренд: Sota Страницы: 7

Бренд: Ebyte Страницы: 7

Бренд: NEBO Страницы: 2

Бренд: HydroHoist Страницы: 19

Бренд: IDENTITES Страницы: 3

Бренд: Vahle Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды