horsch Terrano 4.3 GX Скачать руководство пользователя страница 77

Страница: 77 / 114

Operation | 8

60084498 • 01 • 06/2022 • en

8.2.4 Folding

WARNING

Serious crushing due to lowering / dropping machine parts

No persons may stay under raised machine parts.

Order persons to leave the danger zone around the machine. Make sure be-
fore folding that no persons are present in the danger zone.

Comply with the accident prevention instructions.

WARNING

Risk of accident due to insufficient stability

Fold the machine only after it has been fully connected.

The machine must not be in an inclined position when folding it.

Fold the machine only on a level and firm surface.

Lighting carrier

Terrano 4.3 GX and 4.4 GX

Applies only to these machine types. In addition, adjust the two front lighting carri-
ers for the folding process:

1. Loosen cotter pin and bolt (2).

2. Push both lighting carriers (1) toward the inside.

3. Secure the new position of the lighting carriers with bolt and cotter pin.

Содержание Terrano 4.3 GX



















































































































Результаты поиска

Содержание Terrano 4.3 GX

Отзывы:

Бренды по названию

Популярные бренды

horsch Terrano 4.3 GX, Руководство по эксплуатации

Результаты поиска

Содержание Terrano 4.3 GX

Отзывы:

Бренды по названию

Популярные бренды