manualshive.com logo in svg

horsch Terrano 4.3 GX, Руководство по эксплуатации

Поделиться
Скачать
horsch Terrano 4.3 GX Скачать руководство пользователя страница 14

2 | Safety and responsibility

14

60084498 • 01 • 06/2022 • en

2.7.2 Commissioning

The operational safety of the machine cannot be guaranteed without orderly per-
formed commissioning. This can lead to accidents with severe or even fatal physical
injuries.

Ø

The machine must only be put into operation after receiving instructions by
employees of the authorized dealer or a HORSCH employee.

All protective features and safety equipment, such as detachable protective devices
(wheel chocks, etc.), must be correctly in place and reliably functioning before the
machine is put into operation.

Ø

Check nuts and bolts, especially the ones on wheels and cultivation tools regu-
larly for tight fit and retighten if necessary.

Ø

Check the tyre pressure at regular intervals, see maintenance overview.

2.7.3 Damage to the machine

Damage to the machine can impair the operational safety of the machine and cause
accidents. This can lead to severe or even fatal physical injuries.

The following machine parts are particularly important for safety:

• Hydraulics

• Brakes (if available)

• Connecting features

• Protective features

• Lighting

If in doubt about the safety-relevant status of the machine, e.g. in case of leaking
operating fluids, visible damage or unexpected changes in driving behaviour:

Ø

Immediately shut down and secure the machine.

Ø

If possible, locate and rectify the faults by following these operating instruc-
tions.

Ø

Rectify possible causes for damage (e.g. remove coarse dirt and tighten loose
screws).

Ø

Have damage that could affect safety and that cannot be rectified by you recti-
fied by a qualified expert workshop.

2.7.4 Hitching and uncoupling

Faulty coupling of the machine to the pulling tool of the tractor causes dangers,
which could result in severe accidents.

Ø

Strictly comply with all operating instructions:

• These operating instructions

• Operating instructions of the tractor

Ø

Exercise special caution when reversing the tractor. Never stand between
tractor and machine.

Ø

Only park the machine on a firm and level surface. Before unhitching the
towed machine, lower it to the ground.

Ø

Secure the machine against rolling away.

Содержание Terrano 4.3 GX



















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды