horsch Terrano 4.3 GX Скачать руководство пользователя страница 20

Страница: 20 / 114

2 | Safety and responsibility

60084498 • 01 • 06/2022 • en

Failing to pay attention to the danger zone can result in severe or even fatal physical
injuries.

1. Do not stand under lifted loads. Lower such loads to the ground first.

2. Instruct persons to leave the danger zone around the machine and tractor be-

fore any machine movements.

3. Before working in the danger zone of the machine or between machine and

tractor:

Shut down the tractor!

This also applies to temporary inspection work.

Many accidents happen because of carelessness and running machines!

4. Pay attention to the information in all operating instructions.

2.9 Safety stickers

Safety stickers on the machine warn of hazards at dangerous points and are an im-
portant part of the safety equipment of the machine. Missing safety stickers increase
the risk of severe or even fatal injuries.

1. Clean soiled safety stickers.

2. Damaged or illegible safety stickers must be replaced immediately.

3. Affix the specified safety stickers on spare parts.

00380055

Before commissioning the machine the operating instruc-
tions must be read and followed!

00380294

Shut the engine down and pull off the key before starting
maintenance and repair work.

00380133

Caution for fluids spraying out under high pressure, follow
the notes in the operating instructions!

Содержание Terrano 4.3 GX



















































































































Результаты поиска

Содержание Terrano 4.3 GX

Отзывы:

Бренды по названию

Популярные бренды

horsch Terrano 4.3 GX, Руководство по эксплуатации

Результаты поиска

Содержание Terrano 4.3 GX

Отзывы:

Бренды по названию

Популярные бренды