horsch Terrano 4.3 GX Скачать руководство пользователя страница 44

Страница: 44 / 114

6 | Assembly groups

60084498 • 01 • 06/2022 • en

Observe the sequence when tightening MulchMix coulter tips together with
guide plates:

Tighten the screw connections for mounting the wings on the nut. Do not
tighten on the screw head.

Tighten all screw connections with a nut runner or torque spanner.

Observe the tightening torque: 160 ± 10 Nm

6.3 Packer

WARNING

The packers may continue to turn when stepping on them causing
falls with serious injuries.

Do not step on the packers.

In the working position the machine runs on the packer. The weight of the machine
causes high compaction and a fine crumbly, level surface.

With cohesive soils the packers may pick up soil and thus become considerably
heavier. This can cause overloads and damage to components, or may dirty roads
during transportation.

NOTE

Remove any picked up soil prior to road travel and regularly during field work
from the packer.

Содержание Terrano 4.3 GX



















































































































Результаты поиска

Содержание Terrano 4.3 GX

Отзывы:

Бренды по названию

Популярные бренды

horsch Terrano 4.3 GX, Руководство по эксплуатации

Результаты поиска

Содержание Terrano 4.3 GX

Отзывы:

Бренды по названию

Популярные бренды