horsch Terrano 4.3 GX Скачать руководство пользователя страница 30

Страница: 30 / 114

4 | Technical data

60084498 • 01 • 06/2022 • en

4.3.1 Calculating the ballasting

The permissible total weight, the permissible axle loads and the tyre load bearing ca-
pacity must not be exceeded when mounting or connecting implements.

The front axle of the tractor must always be loaded with at least 20 % of the curb
weight of the tractor.

Check before road transport whether the tractor used is suitable for this imple-
ment and whether it is not overloaded.

Weigh the implement separately. Since different equipment variants are pos-
sible, the weight of the implement must be determined by weighing.

Required data

Curb weight of tractor

Front axle load of empty tractor

Rear axle load of empty tractor

• Total weight of rear implement

• In case of towed machines:

Maximum permissible drawbar load for road transport.

Total weight of front implement/front ballast

Distance from front implement/front ballast centre of gravity to middle of
front axle

Tractor wheel base

• Distance from middle of rear axle to middle of tractor link arm ball.

• In case of towed machines:

Distance from middle of rear axle to middle of lifting point.

• Distance from middle of tractor link arm ball to centre of gravity of rear

mounted implement/rear ballast.

• The following applies to towed machines: d = 0.

Information of tractor manufacturer for minimum rear ballasting.
If no information is available, enter 0.45.

All specified weights in kg [lbs].

All dimensions in m [ft/in].

• * The centre of gravity of the machines cannot be specified exactly because of

optional equipment. Enter half the machine length for calculation.

Содержание Terrano 4.3 GX



















































































































Результаты поиска

Содержание Terrano 4.3 GX

Отзывы:

Бренды по названию

Популярные бренды

horsch Terrano 4.3 GX, Руководство по эксплуатации

Результаты поиска

Содержание Terrano 4.3 GX

Отзывы:

Бренды по названию

Популярные бренды