Honeywell Ademco Vista-12D Скачать руководство пользователя

Страница: 72 / 112

Installation and Setup Guide

5-16

For example,

if you want to pulse a strobe light upon fire alarms on zone 4 using a relay

mapped to output number 2 (as programmed in *79 Menu Mode), program the following in
*80 Menu Mode:

Prompt Entry

Output Funct. #

= 01 (assuming this is the first output function)

Activated By:

= 3 (zone number)

Enter Zn No.

= 04 (requires 2-digit zone numbers)

Output Action

= 3 (continuous pulse)

Output Number

= 02 (device mapped in *79 Menu Mode)

Start Output Definition mode by pressing

•

80 while in Data Programming mode. The

following prompts are displayed:

∗∗∗∗

80 Menu Mode

PROMPT

VALID ENTRIES

EXPLANATION

Output Funct. #

(00 = Quit)

Output Function No.

01-12 = output function number
[

∗

] to continue

Enter the output function number to be defined
(or 00 to exit).

01 A E P Trig

?00 0 0 – ZL=1

Summary Screen

[

∗

] to continue

This screen displays a summary of the current
output programming (for this example, Zone List
has been selected-this is the default screen).

= Output Action;

= Triggering event;

Partition;

Trig

= Trigger type

NOTE:

A question mark in the summary screen

indicates that the device number shown has not
been mapped. Use *79 Menu mode to map the
device.

01 Activated By:

Zone List

Activated By

0 = delete
1 = zone list
2 = zone type
3 = zone number
[

∗

] to continue

Select where the initiating event for this output
definition is to occur as follows:
0 = delete (deletes the output function and any

previous programming;-see prompt below)

1 = zone list (go to “A” prompt)

2 = zone type (go to “B” prompt)

3 = zone number (go to “C” prompt)

If you enter “0,” the following prompt appears:

Delete?

Press 1 to delete this

0 = NO, 1 = YES

output definition.

Содержание Ademco Vista-12D
















































































































Результаты поиска

Содержание Ademco Vista-12D

Отзывы:

Похожие инструкции для Ademco Vista-12D

Бренды по названию

Популярные бренды

Honeywell Ademco Vista-12D, Инструкция по установке и настройке

Результаты поиска

Содержание Ademco Vista-12D

Отзывы:

Похожие инструкции для Ademco Vista-12D

Бренды по названию

Популярные бренды