Honeywell Ademco Vista-12D Скачать руководство пользователя страница 7

Страница: 7 / 112

Features and Installation Highlights

1-3

Important Installation Highlights (Installer Please Read)

•

This system uses addressable keypads and a Zone Expander Module (see table of

addresses in

Programming Overview

section).

•

Keypads must be set for addresses 16-23 (first keypad is address 16, which is different

from previous controls) and programmed in data fields *190-*196.

•

Zone Expander Module must be set for specific address (08), based on the zone numbers

used
(see table of addresses in

4219/4229 Expansion Zones

section).

•

4204 Relay Module must be set for specific address (13; see

Connecting Relay

Modules

section).

•

6164 Keypads must be set for two addresses: a keypad address and a zone expander

address (if using the keypad’s expansion zones).

•

This control will not power-up unless AC mains is connected (will not power-up on

battery alone). However, once the system is powered up, it will operate on battery power
in the event of AC mains loss.

•

Relays have two programming menu modes: Use *79 Menu mode to map module

addresses and device (output) numbers. Use *80 Menu mode to define the output
functions (see

Output Device Programming

section).

•

This system supports programmable function keys. Use *57 Menu mode to define the

function keys (see

Function Key Programming

section).

•

This system provides various paging features. Refer to the

Programming Overview

section for a summary on pager programming.

Содержание Ademco Vista-12D
















































































































Результаты поиска

Содержание Ademco Vista-12D

Отзывы:

Бренды по названию

Популярные бренды

Honeywell Ademco Vista-12D, Инструкция по установке и настройке

Результаты поиска

Содержание Ademco Vista-12D

Отзывы:

Бренды по названию

Популярные бренды