Honeywell Ademco Vista-12D Скачать руководство пользователя страница 18

Страница: 18 / 112

Installation and Setup Guide

2-10

6164 Keypad Expansion Zones

1. Connect each keypad to the control’s keypad

terminals.

2. Using the keypad’s program mode, assign the

keypad a unique keypad address (16-23), and
assign a device address of 08 which provides
expansion zones 17-20.

3. Connect sensors to the keypad’s zone

terminals.

4. If using the keypad relay, connect the desired

field wiring to the keypad's relay contact
terminals.

See 6164 Keypad Instructions for other
mounting, wiring, and programming
information.

Notes

•

Each 6164 keypad supports up to 4 wired

expansion EOLR or double-balanced zones
and one relay output.

•

Use 2000 ohm end-of-line resistors at the

end of loops connected to the 6164 keypads.

•

Enter 6164 keypad program mode by

pressing and holding down both the [1] and
[3] keys within 60 seconds of power up.

•

Enable the keypad addresses using data

fields *191-*196 as required.

•

Program keypad zones using *56 Menu

mode. Keypad zones 1-4 correspond to the
respective groups of zones shown in the
chart at left, where keypad zone 1 is the
lowest zone number in each group.

[-] GROUND (-

(Z1

Z2)

(Z3

Z4)

TAMPER

CONTACTS

TAMPER

CONTACTS

N.O.

N.C.

DOUBLE BALANCED

CONVENTIONAL
EOLR

[Y] DATA IN (<)

[+] +12VDC IN

[G] DATA OUT

OPTIONAL

Y +

N.O.

N.C.

Содержание Ademco Vista-12D
















































































































Результаты поиска

Содержание Ademco Vista-12D

Отзывы:

Бренды по названию

Популярные бренды

Honeywell Ademco Vista-12D, Инструкция по установке и настройке

Результаты поиска

Содержание Ademco Vista-12D

Отзывы:

Бренды по названию

Популярные бренды