Honeywell Ademco Vista-12D Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 112

Honeywell Ademco Vista-12D Скачать руководство пользователя страница 20

Installation and Setup Guide

2-12

Installing the Transmitters

1. To be sure reception of the transmitter's signal

at the proposed mounting location is adequate,
perform a Go/No Go Test (see the

Testing the

System

section).

2. Install transmitters in accordance with the

instructions provided with each.

3. Set 5827, 5827BD, 5804BD wireless keypads to

the programmed House ID (field *24), using its
DIP switches (5827) or follow the instructions
provided with the device.

Notes

•

Refer to the table of compatible devices at

the back of this manual.

•

Supervised transmitters

†

send check-in signals

to the receiver at 70-90 minute intervals. If at
least one check-in message is not received from
each transmitter within a 12-hour period, the
“missing” transmitter number(s) and “CHECK
is displayed.

†

Hand-held transmitters (e.g., 5802, 5802CP, 5804,

5804BD, 5827, 5827BD) do not send check-in
signals.

Transmitter Battery Life

• See Wireless Transmitter paragraph in the

Limitations of This Alarm System

statement located

at the end of this manual for information on transmitter battery life.

• Some transmitters (e.g., 5802 and 5802CP) contain long-life but non-replaceable batteries, and no

battery installation is required. At the end of their life, the complete unit must be replaced (and a
new serial number enrolled by the control).

• Button-type transmitters (such as 5801, 5802, and 5802CP) should be periodically tested for

battery life.

• The 5802EU, 5802MN, 5802MN2, 5804EU, and 5804 Button Transmitters have replaceable

batteries.

Do not install batteries in wireless transmitters until you are ready to enroll during system
programming. After enrolling, batteries need not be removed.

Installing a Keyswitch

1. Connect the 4146 keyswitch's normally open

momentary switch to a zone’s terminals
(zones 2-8). Remove the 2000 ohm EOL
resistor if connected across the selected zone.

2. Using a standard keypad cable as shown:

Connect the yellow and white keyswitch wires
to trigger connector pin 3 (+12V).

Connect the Red and Green LED wires to the
appropriate output 17/output 18 trigger
connector pins.

3. Connect a 2000 ohm EOL resistor across the

momentary switch.

4. You can wire an optional closed-circuit

tamper switch (model 112) in series with the
zone. If the switchplate is then removed from
the wall, the tamper will open, disabling
keyswitch operation until the system is next
disarmed from the keypad.

If the tamper is opened when the system is
armed, an alarm will occur.

Notes

•

Use 4146 keyswitch or any normally open

keyswitch.

•

Use only one keyswitch per partition.

•

If using a keyswitch in more than one partition,

you must use relays (not the on-board triggers)
for the Red/Green LED functions (step 2).

•

When using a keyswitch, the zone it is

connected to is no longer available for use as a
protective zone.

•

Use *56 Menu mode to program the keyswitch

zone and assign it zone type 77.

•

Use *80 Menu mode to program the LED

functions: program outputs 17 and 18 for
system operation zone type 78 (red LED)
and 79 (green LED) as appropriate (see

Output Device Programming

section).

«
...
18
19
20
21
22
...
»

Содержание Ademco Vista-12D

















































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды