manualshive.com logo in svg

Hitachi SJ700B SERIES, Инструкция по эксплуатации

Инструкция по эксплуатации для серии Hitachi SJ700B - бесплатно скачать с manualshive.com. Ознакомьтесь с подробным руководством по эксплуатации этого продукта, чтобы оптимизировать его использование. Не упустите возможность загрузить руководство прямо сейчас на manualshive.com.

Поделиться
Скачать
background image

Chapter 4 Explanation of Functions

 

4 - 69 

4.2.72 Low-current indication (LOC) signal 

The inverter outputs the low-current indication (LOC) 
signal when the inverter output current falls to the 
low-current indication signal detection level (C039) or 
less. 
You can select one of the two signal output modes with the low-current indication signal output mode 
selection (C038). In one mode, the LOC signal output is always enabled during the inverter operation. In 
the other mode, the LOC signal output is enabled only while the inverter is driving the motor for 
constant-speed operation. 

Item 

Function code 

Data or range of data

Description 

Terminal function 

C021 to C025 

Alarm relay terminal function 

C026 

43 

LOC: Low-current indication signal 

00 

Enabling the signal output during 

operation 

Low-current indication signal 

output mode selection 

C038 

01 

Enabling the signal output only 

during constant-speed operation (*1

Low-current indication signal 

detection level 

C039 

0.0 to 1.5 x rated 

current (A) 

Setting of the threshold current level 

at which to output the low-current 

indication signal 

(*1) When 01 (control circuit terminal) is selected as frequency source setting (A001), there is a case that 
inverter does not recognize the speed as constant value due to sampling. In this case, adjusting is to be 
made by setting C038=00 (valid during operation) or increasing analogue input filter (A016).     
 
 
 
 
 
 
 
 
 
 
 
 
 
 

4.2.73 Inverter ready signal (IRDY) 

The inverter outputs the inverter ready (IRDY) signal when it is ready 
for operation (i.e., when it can receive an operation command). 
- The inverter can recognize only the operation command that is input while the IRDY signal is output. 
- If the IRDY signal is not output, check whether the input power supply voltage (connected to the R, S, and T 
terminals) is within the range of specification. 
- Signal is not output when the power is given only to control power supply.

 

Item 

Function code 

Data or range of data

Description 

Terminal function 

C021 to C025 

Alarm relay terminal function 

C026 

50 

IRDY: Inverter ready signal 

 

4.2.74 Forward rotation signal (FWR) 

The inverter continues to output the forward rotation (FWR) signal 
while it is driving the motor for forward operation. 
The FWR signal is turned off while the inverter is driving the motor for 
reverse operation or stopping the motor.

 

Item 

Function code 

Data or range of data

Description 

Terminal function 

C021 to C025 

Alarm relay terminal function 

C026 

51 FWR: 

Forward 

rotation 

signal 

C021 to C025: Terminal [11] to [15] functions 
C026: Alarm relay terminal function 
C038: Low-current indication signal output mode selection 
C039: Low-current indication signal detection level 

Related code 

C021 to C025: Terminal [11] to [15] functions 
C026: Alarm relay terminal function 

Related code 

C021 to C025: Terminal [11] to [15] functions 
C026: Alarm relay terminal function 

Related code 

 

 

 

Output current (A) 

Low-current indication 
signal detection level 
(C039) 

Low-current 
indication signal 

ON

ON

Содержание SJ700B SERIES




















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SJ700B SERIES

Datavideo DAC-9 Quick Start Manual preview
DAC-9
Бренд: Datavideo Страницы: 10
VAD DAC-10 User Manual preview
DAC-10
Бренд: VAD Страницы: 18
TDT RV2 Manual preview
RV2
Бренд: TDT Страницы: 18
Ginlong Solis-100K-HV-5G Installation And Operation Manual preview
Solis-100K-HV-5G
Бренд: Ginlong Страницы: 28
NF DF 1906 Instruction Manual preview
DF 1906
Бренд: NF Страницы: 96
Williams AV FM T55 Quick Start Manual preview
FM T55
Бренд: Williams AV Страницы: 2
OTS ET1111 Series Manual preview
ET1111 Series
Бренд: OTS Страницы: 3
Barco NGS-D220 Quick Start Manual preview
NGS-D220
Бренд: Barco Страницы: 2
AJA Hi5-3D Installation And Operation Manual preview
Hi5-3D
Бренд: AJA Страницы: 29
Cross Technologies 2016-95 Instruction Manual preview
2016-95
Бренд: Cross Technologies Страницы: 18
IO-Power Technology Cloudy-Solar Collection IOP-USSS-12V1224-OA Series User Manual preview
Cloudy-Solar Collection IOP-USSS-12V1224-OA Series
Бренд: IO-Power Technology Страницы: 22
Gyrus Acmi PlasmaKinetic User Manual preview
PlasmaKinetic
Бренд: Gyrus Acmi Страницы: 60
Wyrestorm NetworkHD 100 series Quick Start Manual preview
NetworkHD 100 series
Бренд: Wyrestorm Страницы: 2
IMO ISOCON-6 User Manual preview
ISOCON-6
Бренд: IMO Страницы: 16
Heyner MobilePower PRO Instruction Manual preview
MobilePower PRO
Бренд: Heyner Страницы: 4
Drivecon VF61 Function Manual preview
VF61
Бренд: Drivecon Страницы: 28
PEC MACC Manual preview
MACC
Бренд: PEC Страницы: 26
V-TAC VT-6603105 Instruction Manual preview
VT-6603105
Бренд: V-TAC Страницы: 37

Бренды по названию

Популярные бренды

Загрузить еще бренды