manualshive.com logo in svg

Hitachi SJ700B SERIES, Инструкция по эксплуатации

Инструкция по эксплуатации для серии Hitachi SJ700B - бесплатно скачать с manualshive.com. Ознакомьтесь с подробным руководством по эксплуатации этого продукта, чтобы оптимизировать его использование. Не упустите возможность загрузить руководство прямо сейчас на manualshive.com.

Поделиться
Скачать
background image

Chapter 4 Explanation of Functions

 

4 - 65 

4.2.64 Over-torque signal (OTQ) 

The inverter outputs the over-torque signal when it detects 
that the estimated motor output torque exceeds the 
specified level. 
To enable this function, assign function "07" (OTQ: 
over-torque signal) to an intelligent output terminal.   
This function is effective only when the V/F characteristic curve selection selected with function "A044" or 
"A244" is the sensorless vector control, 0Hz-range sensorless vector control, or vector control with sensor. 
With any other V/F characteristic curve selection, the output of the OTQ signal is unpredictable. 
When using the inverter for a lift, use the OTQ signal as the trigger to stop braking. Use the 
frequency-arrival signal as the trigger to start braking. 

Item 

Function code 

Set value 

Description 

Terminal function 

C021 to C025 

Alarm relay terminal function 

C026 

07 

OTQ: Over-torque signal 

Over-torque (forward-driving) level 

setting 

C055 

0. to 150. (%)

Threshold level to output the OTQ signal 

during forward powering operation 

Over-torque (reverse 

regenerating) level setting 

C056 

0. to 150. (%)

Threshold level to output the OTQ signal 

during reverse regeneration operation 

Over-torque (reverse driving) level 

setting 

C057 

0. to 150. (%)

Threshold level to output the OTQ signal 

during reverse powering operation 

Over-torque (forward 

regenerating) level setting 

C058 

0. to 150. (%)

Threshold level to output the OTQ signal 

during forward regeneration operation 

 

4.2.65 Alarm code output function (AC0 to AC3) 

The alarm code output function allows you to make the inverter 
output a 3- or 4-bit code signal as the trip factor when it has 
tripped. 
Specifying "01" (3 bits) or "02" (4 bits) for the alarm code output (C062) forcibly assigns the alarm code 
output function to intelligent output terminals [11] to [13] or [11] to [14], respectively. 
The following table lists the alarm codes that can be output: 

Intelligent output terminals

When "4 bits" is selected 

When "3 bits" is selected 

14 13 12 11 

AC3 AC2 AC1 AC0

Factor code 

Cause of tripping 

Factor code 

Cause of tripping 

0 0 0 0  Normal Normal 

operation 

Normal  Normal 

0 

0 

0 

1 

E01 to E03,E04 Overcurrent protection 

E01 to E03, E04  Overcurrent protection

0 0 1 0  E05, 

E38 

Overload protection 

Low-speed overload 

protection 

E05 

Overload protection 

Low-speed overload 

protection 

0 0 1 1  E07, 

E15 

Overvoltage/input 

overvoltage protection 

E07, E15 

Overvoltage/input 

overvoltage protection 

0 1 0 0 

E09  Undervoltage 

protection 

E09  Undervoltage 

protection

0 1 0 1 

E16  Instantaneous power failure 

protection 

E16 

Instantaneous power 

failure protection 

0 1 1 0 

E30  IGBT 

error 

E30  IGBT 

error 

0 1 1 1 

E06  Braking resistor overload 

protection 

－

 Other 

error 

1 0 0 0 

E08, E11, E23

E25 

EEPROM, CPU, GA 

communication, or main 

circuit error 

－

 

－

 

1 0 0 1 

E10  CT 

error 

－

 

－

 

1 0 1 0 

E12, E13, E35,

E36 

External trip, USP error, 

thermistor error, or braking 

error 

－

 

－

 

1 0 1 1 

E14  Ground-fault 

protection 

－

 

－

 

1 1 0 0 

E43, 

E44, 

E45

Invalid instruction in easy 

sequence 

Nesting error in easy 

sequence 

Easy sequence execution 

command error 

－

 

－

 

A044/A244/A344: V/F characteristic curve selection, 
1st/2nd/3rd motors 
C021 to C025: Terminal [11] to [15] functions 
C055: Over-torque (forward-driving) level setting 
C056: Over-torque (reverse regenerating) level setting 
C057: Over-torque (reverse driving) level setting 
C058: Over-torque (forward regenerating) level setting 

Related code 

C021 to C025: Terminal [11] to [15] functions 
C062: Alarm code output 

Related code 

Содержание SJ700B SERIES




















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SJ700B SERIES

XSY AT Series Manual preview
AT Series
Бренд: XSY Страницы: 22
Y-Solar T10 Series User Manual preview
T10 Series
Бренд: Y-Solar Страницы: 5
YASKAWA A1000 Series Product Replacement Manual preview
A1000 Series
Бренд: YASKAWA Страницы: 44
Yamaha ACU16-C Manual preview
ACU16-C
Бренд: Yamaha Страницы: 32
Goobay 60267 User Manual preview
60267
Бренд: Goobay Страницы: 24
Pulsar DC/DC20SD Quick Start Manual preview
DC/DC20SD
Бренд: Pulsar Страницы: 4
NSM TBM 160 MB Use And Maintenance Manual preview
TBM 160 MB
Бренд: NSM Страницы: 24
Baumer GTR 9 Mounting And Operating Instructions preview
GTR 9
Бренд: Baumer Страницы: 24
RME Audio M-32 DA User Manual preview
M-32 DA
Бренд: RME Audio Страницы: 68
Samlexpower SA-1000K Series User Manual preview
SA-1000K Series
Бренд: Samlexpower Страницы: 23
Inside Out Networks Digi Edgeport/1i Installation Manual preview
Digi Edgeport/1i
Бренд: Inside Out Networks Страницы: 22
DVDO DVDO-VGAHDMI-1 User Manual preview
DVDO-VGAHDMI-1
Бренд: DVDO Страницы: 9
MPP Solar 2424LV-HS User Manual preview
2424LV-HS
Бренд: MPP Solar Страницы: 46
Microchip Technology MCP1623/4 Reference Design preview
MCP1623/4
Бренд: Microchip Technology Страницы: 28
Sonoro MEISTERSTUCK Quick Start Manual preview
MEISTERSTUCK
Бренд: Sonoro Страницы: 40
Harman AMX N Series Quick Start Manual preview
AMX N Series
Бренд: Harman Страницы: 8
Yangzhou Shenzhou Wind-driven Generator FD2.1-200-8L User Manual preview
FD2.1-200-8L
Бренд: Yangzhou Shenzhou Wind-driven Generator Страницы: 35
NSK Varios 170 Operation Manual preview
Varios 170
Бренд: NSK Страницы: 52

Бренды по названию

Популярные бренды

Загрузить еще бренды