Hitachi H8S/2215 Series Скачать руководство пользователя страница 230 | Manualshive

Страница: 230 / 745

background image

Rev. 3.0, 10/02, page 172 of 686

7.4.5

Normal Mode

In normal mode, transfer is performed with channels A and B used in combination. Normal mode
can be specified by setting the FAE bit in DMABCR to 1 and clearing the BLKE bit in DMACRA
to 0. In normal mode, MAR is updated after each byte or word transfer in response to a single
transfer request, and this is executed the number of times specified in ETCRA. The transfer source
is specified by MARA, and the transfer destination by MARB. Table 7.6 summarizes register
functions in normal mode.

Table 7.6

Register Functions in Normal Mode

Register

Function

Initial Setting

Operation

23

0

MARA

Source address
register

Start address of
transfer source

Incremented/decremented
every transfer, or fixed

23

0

MARB

Destination address
register

Start address of
transfer destination

Incremented/decremented
every transfer, or fixed

0

15

ETCRB

Transfer counter

Number of transfers Decremented every

transfer; transfer ends
when count reaches
H'0000

MARA and MARB specify the start addresses of the transfer source and transfer destination,
respectively, as 24 bits. MAR can be incremented or decremented by 1 or 2 each time a byte or
word is transferred, or can be fixed. Incrementing, decrementing, or holding a fixed value can be
set separately for MARA and MARB.

The number of transfers is specified by ETCRA as 16 bits. ETCRA is decremented each time a
transfer is performed, and when its value reaches H'0000 the DTE bit is cleared and transfer ends.
If the DTIE bit is set to 1 at this time, an interrupt request is sent to the CPU or DTC. The
maximum number of transfers, when H'0000 is set in ETCRA, is 65,536.

«
...
228
229
230
231
232
...
»

Содержание H8S/2215 Series










































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для H8S/2215 Series

Бренд: National Instruments Страницы: 85

Бренд: National Instruments Страницы: 9

FIELDPOINT FP-1600

Бренд: National Instruments Страницы: 8

Бренд: PaloAlto Networks Страницы: 3

Бренд: ZALMAN Страницы: 7

Бренд: Digi Страницы: 116

Бренд: Aaeon Страницы: 61

Бренд: MSNswitch Страницы: 2

Бренд: Technics Страницы: 20

Бренд: Acromag Страницы: 23

Бренд: Top Страницы: 21

Бренд: Powerleap Страницы: 28

Бренд: ASROCK Страницы: 173

Бренд: Rosewill Страницы: 2

Бренд: Corsair Страницы: 10

Бренд: NetBurner Страницы: 30

Бренд: Idis Страницы: 16

ENHANCED PSD 239 H2R

Бренд: ADTRAN Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды