Hitachi H8S/2215 Series Скачать руководство пользователя страница 360 | Manualshive

Страница: 360 / 745

background image

Rev. 3.0, 10/02, page 302 of 686

10.5.4

PWM Modes

In PWM mode, PWM waveforms are output from the output pins. 0, 1, or toggle output can be
selected as the output level in response to compare match of each TGR. Settings of TGR registers
can output a PWM waveform in the range of 0 % to 100 % duty. Designating TGR compare match
as the counter clearing source enables the period to be set in that register. All channels can be
designated for PWM mode independently. Synchronous operation is also possible. There are two
PWM modes, as described below.

•

PWM mode 1

PWM output is generated from the TIOCA and TIOCC pins by pairing TGRA with TGRB and
TGRC with TGRD. The output specified by bits IOA3 to IOA0 and IOC3 to IOC0 in TIOR is
output from the TIOCA and TIOCC pins at compare matches A and C, and the output specified
by bits IOB3 to IOB0 and IOD3 to IOD0 in TIOR is output at compare matches B and D. The
initial output value is the value set in TGRA or TGRC. If the set values of paired TGRs are
identical, the output value does not change when a compare match occurs. In PWM mode 1, a
maximum 4-phase PWM output is possible.

•

PWM mode 2

PWM output is generated using one TGR as the cycle register and the others as duty registers.
The output specified in TIOR is performed by means of compare matches. Upon counter
clearing by a synchronization register compare match, the output value of each pin is the initial
value set in TIOR. If the set values of the cycle and duty registers are identical, the output
value does not change when a compare match occurs. In PWM mode 2, a maximum 7-phase
PWM output is possible by combined use with synchronous operation. The correspondence
between PWM output pins and registers is shown in table 10.18.

Table 10.18 PWM Output Registers and Output Pins

Output Pins

Channel

Registers

PWM Mode 1

PWM Mode 2

TGRA_0

TIOCA0

TGRB_0

TIOCA0

TIOCB0

TGRC_0

TIOCC0

0

TGRD_0

TIOCC0

TIOCD0

TGRA_1

TIOCA1

1

TGRB_1

TIOCA1

TIOCB1

TGRA_2

TIOCA2

2

TGRB_2

TIOCA2

TIOCB2

Note:

In PWM mode 2, PWM output is not possible for the TGR register in which the period is set.

«
...
358
359
360
361
362
...
»

Содержание H8S/2215 Series










































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для H8S/2215 Series

Бренд: TFortis Страницы: 86

Magic WiFi mini Ek

Бренд: Devolo Страницы: 22

Бренд: XNET Страницы: 17

Бренд: protech Страницы: 95

Бренд: ETAS Страницы: 82

CNPS7000A Series

Бренд: ZALMAN Страницы: 9

Бренд: Crystal Vision Страницы: 54

Бренд: HighPoint Страницы: 10

PSJ-VZ58 gen3 OEM

Бренд: Grizzly Страницы: 12

Бренд: NEC Страницы: 47

H8S/2615 Series

Бренд: Renesas Страницы: 28

Selenio SNP-GW-3GX32

Бренд: Imagine communications Страницы: 153

Бренд: NovaStar Страницы: 16

Бренд: Intel Страницы: 57

Бренд: Epson Страницы: 19

Бренд: Epson Страницы: 2

Бренд: Epson Страницы: 23

Бренд: Epson Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды