Hino 238 Скачать руководство пользователя страница 667 | Manualshive

Страница: 667 / 919

background image

DEF SCR SYSTEM (DCU)

5–101

12

Inspect the
engine cool-
ant tempera-
ture sensor

1.

Check the installation of the
engine coolant temperature
sensor.

2.

Make sure there is no dirt or
damage to the engine cool-
ant temperature sensor.

Failure found:
Go to YES.

No failure
found: Go to
NO.

Clean the
engine cool-
ant tempera-
ture sensor
and install it
properly.
If damage was
found, replace
the engine
coolant tem-
perature sen-
sor.
Perform "After-
inspection
work" of
INFORMA-
TION section.

Go to step 13.

13

Inspect the
engine cool-
ant tempera-
ture sensor
unit

Measure the resistance between
the terminals of the engine cool-
ant temperature sensor.
<Tester connections>
Engine coolant temperature sen-
sor
WTM+

–

WTM-

<Standard values>
20



C {68



F}: 2.59

–

2.32 k



80



C {176



F}: 0.326

–

0.310 k



The measure-
ments meet
the standard
value: Go to
YES.

The measure-
ments do not
meet the stan-
dard value: Go
to NO.

Go to step 14.

Replace the
engine cool-
ant tempera-
ture sensor.
Perform "After-
inspection
work" of
INFORMA-
TION section.

14

Check the
operation of
the coolant
shutoff valve
[Hino-DX]

Select [Coolant shutoff valve]
from the [Activation Test] menu
and operate the coolant shutoff
valve.
* When the valve is open: Check if
the pressure inside the down-
stream coolant line is rising by
feeling the line with your hand.
* When the valve is closed: Check
if the pressure inside the down-
stream coolant line is dropping by
feeling the line with your hand.

There is a
change in
pressure when
opening and
closing the
valve: Go to
YES.

There is no
change in
pressure when
opening and
closing the
valve: Go to
NO.

Go to step 15.

Replace the
coolant shut-
off valve.
Perform "After-
inspection
work" of
INFORMA-
TION section.

15

Inspect the
engine cool-
ant lines &
hoses

1.

Make sure there are no
leaks in the engine cooling
system (lines and hoses).

2.

Check the engine cooling
system (lines and hoses)
and check if there are no
disconnections, clogging,
punctures, or cracks.

Failure found:
Go to YES.

No failure
found: Go to
NO.

Repair or
replace the
faulty part.
Perform "After-
inspection
work" of
INFORMA-
TION section.

Go to step 16.

DTC: P142B

DEF pump temperature sensor 1 - rationality

Inspection Procedure

Step

Action

Description

Judgement

Check

(Yes/No)

Yes

No

«
...
665
666
667
668
669
...
»

Содержание 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 238

Бренд: ZAPTEC Страницы: 240

Бренд: Camcar Страницы: 6

ESCALADE FAMILY - SPECIFICATIONS 2011

Бренд: Cadillac Страницы: 1

Бренд: NavLinkz Страницы: 21

Бренд: Magneti Marelli Страницы: 2

PRIME DESIGN HXR-269-E-UM3-80

Бренд: Safe Fleet Страницы: 12

Бренд: rough country Страницы: 4

Бренд: WABCO Страницы: 34

Бренд: POOL-LINE Страницы: 2

Бренд: Mazda Страницы: 3

Бренд: Pontiac Страницы: 486

CHALLENGER GK-6125A 2018

Бренд: Coolster Страницы: 45

Бренд: Lock'er Down Страницы: 2

Auto-Dimming Mirror

Бренд: Mazda Страницы: 2

Бренд: Rosco Страницы: 12

Auto Security AA-9103N

Бренд: Audiovox Страницы: 1

Бренд: Jaeger Страницы: 13

Бренд: Vauxhall Страницы: 215

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды