Hino 238 Скачать руководство пользователя страница 492

Страница: 492 / 919

ENGINE CONTROL SYSTEM (J08E)

4–1269

INSPECTION PROCEDURE: P259F

Connect the vehicle to Hino-DX.

Set the starter switch to the "ON" position.

Check if any DTC other than P259F (for example, U010C) has
been detected in [Fault Information].

HINT
Due to CAN communication failures, P259F may have been
detected.

YES

Set the starter switch to the "ON" position.

Select [Engine] and check if P259F has been detected in [Fault
Information].

YES

Check the DTC detected 1 (Engine ECU) [Hino-DX]

Select

Engine

SAPH16F010300992

Has a DTC other than P259F been detected?

Go to the diagnostic procedure of a related
DTC.
After repair, go to step 2.

Go to step 3.

Check the DTC detected 2 (Engine ECU) [Hino-DX]

Select

Engine

SAPH16F010300993

Has DTC P259F been detected?

Go to step 3.

Procedure completed.
Perform "After-inspection work" of INFOR-
MATION section.

Содержание 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 238

Отзывы:

Похожие инструкции для 238

Бренды по названию

Популярные бренды

Hino 238, Руководство по ремонту

Результаты поиска

Содержание 238

Отзывы:

Похожие инструкции для 238

Бренды по названию

Популярные бренды