Hino 238 Скачать руководство пользователя страница 424

Страница: 424 / 919

ENGINE CONTROL SYSTEM (J08E)

4–1201

The pressure is disturbed at a given speed and the pressure
decreases at higher speed.



Replace the supply pump.

Hunting remains within 10 MPa or more for more than 5 seconds.



Replace the SCV.

The engine stops during pressure relief.



Replace the SCV.

Time

Common rail pressure

Engine speed pattern

The pressure is disturbed
at a given speed and the
pressure decreases at
higher speed.

Remains for 5 seconds or longer.

10 MPa or more

Actual common rail pressure

Target common rail pressure

SAPH16F010300942

Time

Common rail pressure

Engine speed pattern

Remains for 5 seconds or longer.

10 MPa or more

Actual common rail pressure

Target common rail pressure

SAPH16F010300943

Common rail pressure

Accelerator pattern

222 MPa

Time

Actual common rail pressure

Target common rail pressure

SAPH16F010300944

Содержание 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 238

Отзывы:

Похожие инструкции для 238

Бренды по названию

Популярные бренды

Hino 238, Руководство по ремонту

Результаты поиска

Содержание 238

Отзывы:

Похожие инструкции для 238

Бренды по названию

Популярные бренды