manualshive.com logo in svg

Hino 238, Руководство по ремонту

Tascam 238 - многодорожечный кассетный записывающий аппарат с возможностью записи восемью дорожек. Для более подробной информации обращайтесь к руководству пользователя. Скачать бесплатно владельческое руководство можно на manualshive.com. Начните использование сегодня и наслаждайтесь качеством звука!

Поделиться
Скачать
background image

DEF SCR SYSTEM (DCU)

5–339

3. Reset condition

•

After having restored to the normal conditions.

4. Indication, warning or system control regulation when the DTC is set.

•

MIL: ON

•

DEF injection is stopped.

•

NOx purification function is stopped.

5. Symptoms on the vehicle when the DTC is set

<Symptoms on the vehicle due to backup control (fail safe function)>

•

Exhaust gas purification function is declined.

<Symptoms on the vehicle due to malfunction>

•

–

6. Pre-inspection work

•

Check if the battery voltage is in the normal range.

7. After-inspection work

•

Clear all past DTCs.

•

Check if no DTC is stored after test drive.

8. Estimated failure factors

•

Failure of NOx sensor 2 (SCR downstream)

- Failure of circuit inside sensor

- Failure of NOx sensor controller

Содержание 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 238

kaarta STENCIL PRO Assembly & Use preview
STENCIL PRO
Бренд: kaarta Страницы: 29
Jeep GRAND CHEROKEE 2023 Information Manual preview
GRAND CHEROKEE 2023
Бренд: Jeep Страницы: 108
FormFit HD 23A 07 Installation Instructions preview
HD 23A 07
Бренд: FormFit Страницы: 4
Whispbar K611W Fitting Instructions Manual preview
K611W
Бренд: Whispbar Страницы: 77
minnid 1.240.344 Operating Instructions Manual preview
1.240.344
Бренд: minnid Страницы: 44
Saab 2008 9-5 Owner'S Manual preview
2008 9-5
Бренд: Saab Страницы: 288
Sunsky S-GPS-0142 User Manual preview
S-GPS-0142
Бренд: Sunsky Страницы: 9
Menabo JUZA Fitting Instructions Manual preview
JUZA
Бренд: Menabo Страницы: 12
Ecco EC4210B-K Installation And Operation Instructions Manual preview
EC4210B-K
Бренд: Ecco Страницы: 9
Subaru Impreza 2.5GT Specifications preview
Impreza 2.5GT
Бренд: Subaru Страницы: 2
Subaru 1999 Impreza Owner'S Manual preview
1999 Impreza
Бренд: Subaru Страницы: 328
THIEYE CarView 2 User Manual preview
CarView 2
Бренд: THIEYE Страницы: 88
Paser UNICOM JVC Installation Manual preview
UNICOM JVC
Бренд: Paser Страницы: 2
Xblitz XME PRO User Manual preview
XME PRO
Бренд: Xblitz Страницы: 56
Ford ALCON 1968 Owner'S Manual preview
ALCON 1968
Бренд: Ford Страницы: 52
Mont Blanc ACTIVA+ Assembly Instructions preview
ACTIVA+
Бренд: Mont Blanc Страницы: 2
T.J.M. T13 Outback Frontal Protection System Fitting Instructions Manual preview
T13 Outback Frontal Protection System
Бренд: T.J.M. Страницы: 18
Audi PXDXVW3 Quick Start Manual preview
PXDXVW3
Бренд: Audi Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды