Hino 238 Скачать руководство пользователя страница 875 | Manualshive

Страница: 875 / 919

background image

DEF SCR SYSTEM (DCU)

5–309

CHECKLIST: P2204

DTC: P2204

NOx sensor (SCR upstream) - Feedback

Inspection Procedure

Step

Action

Description

Judgement

Check

(Yes/No)

Yes

No

1

Check the
DTC detected
(DCU) [Hino-
DX]

Check if any DTC other than
P2204 (for example, P2202,
P2203, P2209, U029D) has been
detected in [DCU].

DTC other
than P2204
(for example,
P2202, P2203,
P2209,
U029D) has
been detected:
Go to YES.

No DTC has
been detected:
Go to NO.

Go to diagno-
sis procedure
of a related
DTC.

Go to step 2.

2

Inspect the
NOx sensor 1
(SCR
upstream)
[Hino-DX]

Swap the NOx sensor 1 (SCR
upstream) and NOx sensor 2
(SCR downstream), connect them
and check if DTCP2204 has been
detected.

1.

Install NOx sensors 1 and 2
in the vehicle, in their oppo-
site location.

2.

Erase the malfunction his-
tory using Hino-DX.

3.

Perform the DPR forced
regeneration. Check if
P2204 has been detected in
[DCU].

DTC P2204
has been
detected: Go
to YES.

No DTC has
been detected:
Go to NO.

Go to step 3.

Replace the
NOx sensor 1
Perform "After-
inspection
work" of
INFORMA-
TION section.

3

Inspect the
engine cool-
ant tempera-
ture sensor

1.

Check the installation of the
engine coolant temperature
sensor.

2.

Make sure there is no dirt or
damage to the engine cool-
ant temperature sensor.

Failure found:
Go to YES.

No failure
found: Go to
NO.

Clean the
engine cool-
ant tempera-
ture sensor
and install it
properly.
If damaged,
replace the
engine cool-
ant tempera-
ture sensor.
Perform "After-
inspection
work" of
INFORMA-
TION section.

Go to step 4.

«
...
873
874
875
876
877
...
»

Содержание 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 238

Green Motion DC 22

Бренд: Eaton Страницы: 65

Бренд: TATA Motors Страницы: 161

Бренд: TAUBENREUTHER Страницы: 11

Бренд: Yakima Страницы: 15

Бренд: UltraGauge Страницы: 55

Бренд: Camcar Страницы: 2

Бренд: Horn Tools Страницы: 6

Бренд: Yakima Страницы: 21

Бренд: Van Guard Страницы: 3

Tata Indigo Diesel

Бренд: TATA Motors Страницы: 190

Prime Design HBR-E-FT33B

Бренд: Safe Fleet Страницы: 12

Бренд: v.link Страницы: 12

2003 Silhouette

Бренд: Oldsmobile Страницы: 466

CARWATT CV12-220C150

Бренд: WATT Страницы: 26

Бренд: Dometic Страницы: 24

F-250 Super Duty 2022

Бренд: Ford Страницы: 740

Бренд: Westfalia Страницы: 10

TuneBase F8Z442

Бренд: Belkin Страницы: 162

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды