Hino 238 Скачать руководство пользователя страница 845 | Manualshive

Страница: 845 / 919

background image

DEF SCR SYSTEM (DCU)

5–279

2

Inspect the
DEF injector 1
[Hino-DX]

NOTICE
Prepare a beaker or similar,
plus a larger measuring vessel
for measuring the DEF to be
injected, before perform this
inspection.
(If the vessel is small, there is
dispersion at the time of injec-
tion from the injector, and the
measuring quantity decreases.)

1.

Set the starter switch to the
"LOCK" position.

2.

Remove the DEF injector
from the muffler.

HINT
Refer to the workshop manual
"SELECTIVE CATALYTIC
REDUCTION (SCR)" in the
chapter "EMISSION CONTROL
(J08E)" (S5-CJ08E10* or S5-
UJ08E10*) for removal and
installation of the DEF injector.

3.

Set the starter switch to the
"ON" position.

4.

Select [DCU].

5.

Select [Check functions] on
Hino-DX menu and check
the operation of the DEF
injector.

<Inspection procedure>
(1) Select [Check functions].
(2) Select [DEF addition test].
(3) Perform addition test as
instructed on the Hino-DX screen.
(Perform all three patterns)

NOTICE
When the DEF tank tempera-
ture is -5



C (23



F) or lower,

perform warm-up to raise it to
10



C (50



F) or higher.

HINT
Refer to the section "System
individual function" in the
chapter "HINO Diagnostic
eXplorer" for detail of DEF
addition test.

Operation is
normal: Go to
YES.

Operation is
abnormal: Go
to NO.

Procedure
completed.
DEF crystal
clogging is
considered
resolved.
Perform "After-
inspection
work" of
INFORMA-
TION section.

Go to step 3.

DTC: P20F4

DEF consumption failure

Inspection Procedure

Step

Action

Description

Judgement

Check

(Yes/No)

Yes

No

«
...
843
844
845
846
847
...
»

Содержание 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 238

Бренд: Wagan Страницы: 12

Бренд: Thule Страницы: 12

Бренд: NavLinkz Страницы: 21

Бренд: Axxess Страницы: 8

Бренд: Dodge Страницы: 276

ULTIMATE SPEED 296713

Бренд: walser Страницы: 10

Бренд: Mercedes-Benz Страницы: 373

Бренд: Acura Страницы: 6

Бренд: Skoda Страницы: 324

CARWATT CV12-220C150

Бренд: WATT Страницы: 26

Бренд: Conrad Страницы: 50

Бренд: KLAUS Multiparking Страницы: 72

T13 Outback Frontal Protection System

Бренд: T.J.M. Страницы: 18

Бренд: Audi Страницы: 4

Sprinter Bed System DIY

Бренд: FVC Страницы: 8

Бренд: Safe Fleet Страницы: 28

Бренд: WABCO Страницы: 40

Бренд: Vauxhall Страницы: 215

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды