Hino 238 Скачать руководство пользователя страница 414 | Manualshive

Страница: 414 / 919

background image

ENGINE CONTROL SYSTEM (J08E)

4–1191

•

The calculated EGR cooler efficiency, which is derived from the engine speed, fuel injection rate, EGR gas outlet
temperature, and coolant temperature, does not exceed 65 %. And:

•

The calculated intercooler efficiency, which is derived from the intake temperature sensor, boost pressure sensor,
intake air temperature sensor (intercooler outlet), and atmospheric pressure sensor, exceeds 45

–

65 % (for vehi-

cle speeds 21 and 40 km/h {13 and 25 mph}). And:

•

The difference among the estimated EGR rate calculated from the engine speed and fuel injection rate, the esti-
mated intake manifold temperature calculated from the EGR gas outlet temperature sensor and intake air tem-
perature sensor (intercooler outlet), and the value of the intake air temperature sensor (intake manifold) are
within 40



C {104



F} (when EGR rate is 40 %).

3. Reset condition

•

Just after restoration to normal condition.

4. Indication, warning or system control regulation when the DTC is set.

•

MIL: ON

•

Diag lamp: OFF

5. Symptoms on the vehicle when the DTC is set

<Symptoms on the vehicle due to backup control (fail safe function)>

•

–

<Symptoms on the vehicle due to malfunction>

•

Insufficient output or engine stall because of DPR filter clogging due to abnormal soot buildup

6. Pre-inspection work

•

Check that the battery voltage is in the normal range.

7. After-inspection work

•

Clear all past DTCs.

•

Check that no DTC is stored after test drive.

8. Estimated failure factors

EGR cooler outlet gas temperature sensor:

•

Sensor failure

Circuit supplying coolant to EGR cooler:

•

Coolant leakage from coolant circuit

•

Air incursion due to improper air venting

EGR cooler:

•

Air incursion due to improper air venting

•

Coolant leakage from EGR cooler

•

Deformation of EGR cooler coolant passageway

•

Obstruction due to soot buildup in inlet/outlet of EGR gas passageway

•

Obstruction due to buildup of foreign substances in coolant passageway of EGR cooler.

EGR valve malfunction
Diesel throttle valve malfunction
SCV malfunction
Injector malfunction

«
...
412
413
414
415
416
...
»

Содержание 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 238

Бренд: ZAPTEC Страницы: 64

Бренд: ZAPTEC Страницы: 24

Бренд: Qube Страницы: 19

Бренд: Cadillac Страницы: 32

Бренд: Wagan Страницы: 12

Бренд: RAM Страницы: 20

QuadraTop Adventure Top S

Бренд: Quadratec Страницы: 20

Бренд: Ford Страницы: 256

Бренд: Hank Страницы: 2

Бренд: EUFAB Страницы: 12

Бренд: Omix-Ada Страницы: 6

Бренд: Prorack Страницы: 10

Бренд: Jaeger Страницы: 13

Akerstroms Tx700

Бренд: LXE Страницы: 146

Бренд: Kia Страницы: 58

Бренд: Renault Страницы: 198

Бренд: Hyundai Страницы: 168

Бренд: Lincoln Страницы: 538

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды