Hino 238 Скачать руководство пользователя страница 394

Страница: 394 / 919

ENGINE CONTROL SYSTEM (J08E)

4–1171

Disconnect the exhaust gas temperature sensor (burner outlet)
connector.

Use the electrical tester to measure the resistance between the
terminals of the exhaust gas temperature sensor (burner outlet).

YES

Inspect the exhaust gas temperature sensor (burner outlet) unit

DIT+

DIT-

SAPH16F010300912

Measurement

conditions

Tester connections

Standard values

Starter switch:
LOCK

Exhaust gas tem-
perature sensor
(burner outlet)
DIT+

–

DIT-

0.3

–

1.8



Do the measurements meet the standard value?

Perform DPR forced regeneration.
Procedure completed.
Perform "After-inspection work" of INFOR-
MATION section.

Replace the exhaust gas temperature sensor
(burner outlet).
Perform "After-inspection work" of INFOR-
MATION section.

Содержание 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 238

Отзывы:

Hino 238, Руководство по ремонту, Страница: 394 / 919

Результаты поиска

Содержание 238

Отзывы: