Hino 238 Скачать руководство пользователя страница 257

Страница: 257 / 919

ENGINE CONTROL SYSTEM (J08E)

4–1034

INSPECTION PROCEDURE: P2149

Check the connection of the injector connector (Looseness and
poor contact).

YES

Set the starter switch to the "LOCK" position.

Connect the signal check harness to the engine ECU.

Set the starter switch to the "ON" position.

Use the electrical tester to measure the voltage between the termi-
nals of the engine ECU (signal check harness) and ground.

YES

Inspect the injector connector

Was any failure found?

Connect securely, repair if needed.
Perform "After-inspection work" of INFOR-
MATION section.

Go to step 2.

Inspect the injector power supply

ECU CASE GND
(ECU MOUNTING BOLT)

E18
E38

SAPH16F010300799

Measurement

conditions

Tester connections

Standard values

Starter switch:
ON

Engine ECU (signal
check harness)
IJ2+(E18)

–

Ground

I2+S(E38)

–

Ground

At least 3/4 of bat-
tery voltage

Do the measurements meet the standard value?

Go to step 3.

Go to step 7.

Содержание 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 238

Отзывы:

Похожие инструкции для 238

Бренды по названию

Популярные бренды

Hino 238, Руководство по ремонту

Результаты поиска

Содержание 238

Отзывы:

Похожие инструкции для 238

Бренды по названию

Популярные бренды